User manual NAVMAN W300

[. . . ] 5 min before automatic shutdown** * Press and hold to perform a controlled shutdown. ** When battery power becomes too low to continue operation, a controlled shutdown is automatically executed (current data is saved). W300 1-7 W300 ­ Interface NAVMAN 2. 0 Navman W300 interface 2. 1 Button functions There are two control buttons, and . These buttons are pressed separately or together to turn the unit on and off, cycle through modes, and select mode options. Throughout this guide the button icons are used as follows: = press this button = press this button = press both buttons together Note: where it is required to press and HOLD buttons, a countdown begins. To perform the required action continue to hold until the counter reaches zero; if you release the button sooner the action will not be performed. 2. 2 Display screen PACE kmmi PM km/hmph AVG 8 7 3 2 kJ kcal kglb Cal SYSTEM SET The illustration above shows the complete display capability of the W300. [. . . ] 1) Press 2) Press repeatedly to increase value by 1 (hold to increase values quickly), or press repeatedly to decrease value by 1 (hold to decrease values quickly). 3) Press 4) Press to go to the next option, or hold to leave setup. 4. 1. 6 Set energy units Set energy units (kcal or kJ) for displaying energy (calories) burned when using Cal mode (see Section 5. 1. 4). kcal SYSTEM SET energy units Access this option If necessary, press and hold to turn the power on and enter setup. 4) Press to go to the next option, or hold to leave setup. 1-14 W300 NAVMAN W300 ­ Setup 4. 1. 7 Set speed units Set units for speed (km/h or mph). km km/h SYSTEM SET speed units Access this option If necessary, press and hold to turn the power on and enter setup. 3) Press 4) Press to go to the next option, or hold to leave setup. Note: Distance is displayed in units that correspond to the selected speed units. For example, if you select speed units `km/h', then distance is displayed in `km'. W300 1-15 W300 ­ Setup NAVMAN 4. 1. 8 Set offset (set local time) This option lets you adjust the W300 to display local time*. You only need to do this once, unless operating the unit in a new time zone. current speed pace session distance PACE km km/h To access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Speed mode to clear all* session data. (*Does not clear · Press and hold odometer. ) · Press to go to the next mode. 5. 1. 2 Speed (Average) mode This mode lets you monitor session distance, average speed and pace. average speed pace session distance PACE km km/h AVG To access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Speed (Average) mode · Press and hold to clear all* session data. (*Does not clear odometer. ) · Press to go to the next mode. W300 1-19 W300 ­ Normal operation NAVMAN 5. 1. 3 Odometer mode This mode lets you monitor total distance. total distance km 2 873 Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Odometer mode to clear odometer only. · Press and hold · Press to go to the next mode. Note: The W300 displays distance in units corresponding to speed units (see section 4. 1. 7). 5. 1. 4 Calories mode This mode shows total energy burned for the session, or since last calories reset. total calories kcal Cal Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Calories mode · Press and hold to clear calories only. · Press to go to the next mode 1-20 W300 NAVMAN W300 ­ Normal operation 5. 1. 5 Clock mode Clock mode shows the current time and date. See section 4. 1. 8 for instructions on setting local time. ) current time current date PM Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Clock mode to clear all* session data. · Press to go to the next mode. Note: If GPS signals are not yet obtained a `no GPS' alert is displayed. The antenna icon flashes until GPS signals are received. W300 1-21 W300 ­ Normal operation NAVMAN 5. 1. 6 Timer mode Timer mode lets you monitor session time. session time Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Timer mode to clear all* session data. (*Does not clear · Press and hold odometer. ) · Press to go to the next mode. Note: The timer starts automatically whenever you start moving and stops whenever you stop moving. 1-22 W300 NAVMAN W300 ­ Normal operation 5. 1. 7 Mode operation (overview) modes Speed operating details clear all session data* clear all session data* AVG Speed (AVG) 2 873 Odometer clear odometer only Cal Calories clear calories only Clock clear all session data* clear all session data* Timer (*Does not clear odometer. ) * KEY = press this button = press this button = press both buttons together = press and hold both buttons together W300 1-23 W300 ­ Default settings NAVMAN 6. 0 Restoring default settings ! WARNING: Restoring factory default settings clears all stored data and all user selected settings! To restore all default factory settings 1) make sure the unit is off 2) press and hold to turn the unit on ­ DO NOT RELEASE 3) while holding , press five times When restoring default settings The screen displays the message `reset all' and a counter. [. . . ] SOME STATES AND COUNTRIES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE WARRANTY PERIOD MAY NOT APPLY TO YOU. Each of these disclaimers is in addition to, and does not reduce the effect of, any other disclaimer. No event that voids any warranty of the Product will have any effect on these disclaimers or limitations of liability. This disclaimer will be construed under the laws of New Zealand without regard for any conflict of law rules. [. . . ]