User manual NAVMAN X300

[. . . ] Replace enclosure cover (ensuring lugs at the bottom of the cover are aligned with slots in the enclosure surround), turn D-ring clockwise to seal. ! For best performance: General use = Alkaline Below 5 oC = NiMH If battery power becomes low during operation the battery icon is displayed. battery icon PM constant = low power flashing = approx. 5 min before automatic shutdown** * Press and hold to perform a controlled shutdown. ** When battery power becomes too low to continue operation, a controlled shutdown is automatically executed (current data is saved). X300 1-7 X300 - Interface NAVMAN 2. 0 Navman X300 interface 2. 1 Button functions There are two control buttons, and . These buttons are pressed separately or together to turn the unit on and off, cycle through modes, and select mode options. Throughout this guide the button icons are used as follows: = press this button = press this button = press both buttons together Note: where it is required to press and HOLD buttons, a countdown begins. [. . . ] For example, if you select speed units `km/h', then distance is displayed in `km' and altitude in `m'. 1-14 X300 NAVMAN X300 - Setup 4. 1. 6 Set offset (set local time) This option lets you adjust the X300 to display local time*. You only need to do this once, unless operating the unit in a new time zone. The X300 will perform all functions accurately without adjusting the offset to display your local time. ) Note: If you attempt to change the time offset before all GPS data are obtained, the screen displays `no GPS' and the antenna icon flashes until all GPS data are received. SYSTEM SET Access this option If necessary, press and hold to turn the power on and enter setup. To set local time to start editing (the screen now appears as shown 1) Press below). Press repeatedly until the screen appears as shown above. While in Speed mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). (*Does not clear · Press and hold odometer. ) · Press to go to the next mode. 5. 1. 2 Speed (Average) mode This mode lets you monitor session distance and average speed. session distance average speed km km/h AVG To access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Speed (Average) mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). (*Does not clear odometer. ) · Press to go to the next mode. 1-18 X300 NAVMAN X300 - Normal operation 5. 1. 3 Speed (Maximum) mode This mode lets you monitor session distance and maximum speed. session distance maximum speed km km/h MAX Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Speed (Maximum) mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). · Press and hold · Press to go to the next mode. 5. 1. 4 Odometer mode This mode shows total distance since odometer was last reset. total distance km 872 3 Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Odometer mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). · Press to go to the next mode. Note: The X300 displays distance in units corresponding to speed units (see section 4. 1. 5). X300 1-19 X300 - Normal operation NAVMAN 5. 1. 5 Altitude mode This mode shows total accumulated altitude and the current altitude. accumulated altitude current altitude m m Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Altitude mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). · Press and hold · Press to go to the next mode. Note: The Navman X300 displays altitude in units corresponding to speed units (see section 4. 1. 5). 5. 1. 6 Zone mode When Zone is OFF, the Zone (MIN) and Zone (MAX) options are skipped and zone alerts do not sound. status ZONE SET Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. To set Zone status 1) Press to start editing (zone status flashes). 4) Press to go to the next mode. 1-20 X300 NAVMAN X300 ­ Normal operation 5. 1. 6. 1 Zone (Minimum) This option lets you set the minimum target speed. target speed (MIN) MIN km/h ZONE SET Access this mode See section 5. 1. 6 for access to this mode. 1) Press 2) Press repeatedly to increase value by 0. 5 (hold to increase values quickly), or press repeatedly to decrease value by 0. 5 (hold to decrease values quickly). 3) Press 4) Press to go to the next mode. 5. 1. 6. 2 Zone (Maximum) This option lets you set the maximum target speed. target speed (MAX) MAX km/h ZONE SET Access this mode See section 5. 1. 6 for access to this mode. 2) Press repeatedly to increase value by 0. 5 (hold to increase values quickly), or press repeatedly to decrease value by 0. 5 (hold to decrease values quickly). 4) Press to go to the next mode. X300 1-21 X300 - Normal operation NAVMAN 5. 1. 7 Clock mode Clock mode shows the current time and date. See section 4. 1. 6 for instructions on setting local time. ) current time current date PM Access this mode If necessary, press to turn the power on and start normal operation. Press repeatedly until the screen appears as shown above. While in Clock mode · Press to store current lap data (the screen briefly shows the lap distance, lap number, and lap time that is being stored). [. . . ] SOME STATES AND COUNTRIES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE WARRANTY PERIOD MAY NOT APPLY TO YOU. Each of these disclaimers is in addition to, and does not reduce the effect of, any other disclaimer. No event that voids any warranty of the Product will have any effect on these disclaimers or limitations of liability. This disclaimer will be construed under the laws of New Zealand without regard for any conflict of law rules. [. . . ]