User manual NIKON LS-10 INSTALLATION GUIDE FOR WINDOWS

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NIKON LS-10 INSTALLATION GUIDE FOR WINDOWS. We hope that this NIKON LS-10 INSTALLATION GUIDE FOR WINDOWS user guide will be useful to you.


NIKON LS-10 INSTALLATION GUIDE FOR WINDOWS : Download the complete user guide (16955 Ko)

Manual abstract: user guide NIKON LS-10 INSTALLATION GUIDE FOR WINDOWS

Detailed instructions for use are in the User's Guide.

[. . . ] z Nikon® Coolscan™ Installation Guide for Windows™ ikonIMAGING ELECTRONIC . . . . . I . . . . . I (f) z I I I I I I I Coolscan™ Installation Guide I for the Windows™ Operating System I I I I I I I~--------------~ FCC Radio Frequency Interference Statement for Coolscan This equipment has been tested and fo und to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] • ]P4 provides a connection for an external LED indicator (not included) to indicate SCSI bus activity. If for some reason Coolscan is not visible to you while scanning, you may wish to connect an additional activity LED to the top two pins. Page 28 Nlkon Coolscan Installation Guide for Windows I I I I I I I I I I I I I I I Chapter 3 The SCSI Interface Installing the SCSI Controller Card Into the Computer Installing the SCSI controller card is not difficult, but requires some manual dexterity. Following is a stepby-step procedure for installing the SCSI controller card. If an uninterruptable power supply is in use, follow the manufacturer's instructions for disconnecting this power supply from the computer. Typically, the cover can be removed after loosening screws on the sides and/or rear panels of the computer chassis. The SCSI controller card is a half-length card requiring an 8-bit ISA card slot. The typical ISA computer is equipped with either 8-bit, 16-bit, or EISA connectors. The SCSI controller card will fit into any of these connectors, as shown in Figure 3. 12. It is designed to fit into either a single-connector 8-bit slot or a double-connector 16-bit slot. In this case, it does not couple to the second connector. Computer Motherboard Card "L" bracket mounting hole -----------~ \ -" " (a) Single-Connector Card Slot - - - - - -1-- - - -(b) Double-Connector Card Slot II::::::::::::::::::::::::::::::: II \~, . 0 0 ::::::=~---~~I~ ::~:::~ ::TIII II ::::::::::::::::::::::::::::::: II :: ::~ ::~ ::~ Chassis mountIng bracket - - - - - - - - - - - - - - -- ! -----' Figure 3. 12 The expansion card slots on the computer's motherboard. Remove the lock down screw. Nlkon Coolscan Installation Guidefor Windows Page 29 The SCSI Interface Chapter 3 Remove the lock down screw and slot cover plate at the back of the computer associated with the selected card. Insert the SCSI controller card into the selected slot. Carefully insert the card into the selected slot, making sure it is properly oriented (the component side of the card should face the same direction as the other cards in the computer) and aligned with the connector on the motherboard. The metal bracket should be flush with the back of the computer, with the external SCSI connector protruding out of the back of the computer. Tighten the ~ock down screw. Re-insert the lock down screw removed in Step 4. The hole in the metal bracket should align with the tapped hole at the back of the computer. If it still does not align, confirm that yo u have correctly inserted the card. Care should be taken not to drop the screw into the computer as it can be difficult to remove. Never leave a dropped screw inside the computer. Re-install the computer cover. At this point, the SCSI controller card should be ready to go. If you are installing an LS-IO, please proceed to the section "Setting Up the SCSI Chain - LS-IO. " Page 30 Nlkon Coolscan Installation Guide for Windows I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I Chapter 3 The SCSI Interface Setting Up the SCSI Chain - LS-l OE The LS-lOE can reside at any position in the SCSI chain. The two 50-pin connectors on the rear of Coolscan are both used for this purpose. There are essentially two possible SCSI chain configurations, the two SCSI devices configuration, and the multiple SCSI devices configuration. Connecting Two SCSI Devices In the simplest case, only two devices share the SCSI chain - the SCSI host and the SCSI target device. In our case, the SCSI host is the PC and the SCSI target device is the scanner. This simple configuration is shown in Figure 3. 13. SCSI Connector (a) Computer - SCSI Host _ _ _ _. . . . [. . . ] If a corrective action does not solve the problem, proceed ro the next listed corrective action. If the problem persists after exhausting all of the suggested corrective actions, contact Nikon Technical Support at (516) 547-4311 for assistance. Problem: The Nikon Software Installer reports that it cannot read my thirdparty application disks during the installation, but when I run the third-party installer outside of the Nikon Installer the disks are read with no problem. Action: This problem is due ro an erro r in reading different density med ia. We advise yo u ro install yo ur third-party software first, then update the scan drivers with the Nikon Installer disk. Problem: My system won't boot after I install the Coolscan SCSI controller card. Action: You have an interrupt co nflict. Refer ro the sectio n on setting the SCSI card configuration, which will direct yo u on how ro assign one of three possible interrupts ro yo ur SCSI host card. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE NIKON LS-10 INSTALLATION GUIDE FOR WINDOWS




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NIKON LS-10 INSTALLATION GUIDE FOR WINDOWS will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.