User manual NIKON R10

[. . . ] 3 Never attempt to disassemble or repair the flash unit by yourself, as this could result in you receiving an electric shock and could also cause the unit to malfunction; such malfunction could lead to personal injury. 4 If the flash unit is dropped and damaged, do not touch any exposed interior metal parts. Such parts, especially the speedlight's capacitor and associated parts, could be in a high-charge state and if touched could cause an electric shock. Disconnect the power or remove the batteries and be sure that you do not touch any of the product's electrical components, and then bring the flash unit to your local Nikon dealer or authorized service center for repair. [. . . ] Confirm that the red ready-lights on the SU-800 and SB-R200 are on, then release the shutter. · For details on test firing, refer to page 88. 72 If the red ready-light blinks immediately after shooting In the TTL mode, when the SB-R200 flash has fired at its maximum output and underexposure may have occurred, the red ready-light on the SB-R200 blinks for approx. (The ready-lights on the SU-800 and in the camera's viewfinder do not blink. ) To compensate, set a higher ISO sensitivity or use a wider aperture and reshoot. RS ST SH EG LI E DL IR E W PE S ON/O FF In the M (manual) mode, set the manual flash output level for Groups A and B. Press the [SEL](FUNC. ) button to display the manual flash output level (blinking). Press the [SEL](FUNC. ) button once again and the manual flash output level stops blinking. · Manual flash output level can be set separately for each group. · Manual flash output level can be set in 1 step increment or decrement from M1/1 to M1/64 output level (M1/8 is preset when shipped from the factory). · Pressing the [] or [] button continuously increases or decreases the value quickly. · Manual flash output level blinks during adjustment and stops after blinking six times unless an adjustment is made. The last value to blink is the one that has been set automatically. Details on close-up flash operation and shooting procedures 73 3 Procedures for close-up flash operation Procedures for triple-light close-up flash operation 1 Press the [ON/OFF] buttons to turn on the camera, the SU-800 and SB-R200. · Ensure that the red ready-lights on the SU-800 and SB-R200 are on. · Confirm that Wireless flash, Close-up mode and CLScompatible camera indicators are correctly displayed on the SU-800. 2 Selecting triple-light flash operation. 2 seconds to toggle between "dual-light" and "triple-light" close-up flash operations. · "Dual-light" is preset when shipped from the factory. Display in triple-light closeup flash operation 3 MODE NO AF-ILL A SE READY Setting the flash mode on the SU-800. Press the [MODE] button to set the flash mode to TTL or M (manual). · "TTL" is preset when shipped from the factory. Press the [SEL](FUNC. ) button once again and the flash output level stops blinking. The last value to blink is the one that has been set automatically. · Manual flash output level can be set separately for each group. (M1/8 is preset when shipped from the factory. ) · Press and hold the [] or [] button to quickly increase or decrease the value. · The flash output level ratio blinks during adjustment and stops after blinking six times unless an adjustment is made. The last value to blink is the one that has been set automatically. 8 Setting a channel number on the SU-800. Press the [SEL](FUNC. ) button to display the channel number (blinking). Press the [SEL](FUNC. ) button once again and the channel number stops blinking. The last channel number to blink is the one that has been set automatically. · Select one of the four available channels. · The channel number blinks during adjustment and stops after blinking six times unless an adjustment is made. The last channel number to blink is the one that has been set automatically. CHANNEL 3 2 1 4 9 Setting a channel number on the SB-R200. Rotate the [CHANNEL] select dial on the SB-R200 to set the channel number. [. . . ] 68 x 96 x 58mm (2. 7 x 3. 8 x 2. 3 in. ) These performance specifications are applicable when a fresh battery is used at normal temperatures (20°C/68°F). Specifications and design are subject to change without notice. 130 Wireless Remote Speedlight SB-R200 Electronic construction Guide number Automatic Insulated Gate Bipolar Transistor (IGBT) and series circuitry (for wireless remote flash unit only) 10/33 (ISO 100, m/ft. ), 14/46 (ISO 200, m/ft. ) Angle of coverage Covering light distribution of 24mm lens; 60° (vertical) and 78° (horizontal) Flash mode Recycling time i-TTL, D-TTL, TTL (film-based cameras) M (manual) Approx. 290 Bounce capability Flash head tilts down (toward the optical axis) to 60° with click stops at every 15°, or up to 45° (in the opposite direction) with click stops at every 15°. Flash duration Mounting foot Target light Display Power source Weight Dimensions (W x H x D) Approx. [. . . ]