User manual NILFISK SCRUBTEC 743
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NILFISK SCRUBTEC 743. We hope that this NILFISK SCRUBTEC 743 user guide will be useful to you.
You may also download the following manuals related to this product:
NILFISK SCRUBTEC 743 (2151 ko)
NILFISK SCRUBTEC 743 (999 ko)
NILFISK SCRUBTEC 743 (999 ko)
NILFISK SCRUBTEC 743 (1068 ko)
NILFISK SCRUBTEC 743 (1068 ko)
NILFISK SCRUBTEC 743 (1042 ko)
NILFISK SCRUBTEC 743 (1068 ko)
NILFISK SCRUBTEC 743 (1042 ko)
NILFISK SCRUBTEC 743 (860 ko)
NILFISK SCRUBTEC 743 (860 ko)
NILFISK SCRUBTEC 743 (1042 ko)
NILFISK SCRUBTEC 743 (860 ko)
NILFISK SCRUBTEC 743 (860 ko)
NILFISK SCRUBTEC 743 (2151 ko)
NILFISK SCRUBTEC 743 (999 ko)
NILFISK SCRUBTEC 743 (1068 ko)
NILFISK SCRUBTEC 743 (1042 ko)
Manual abstract: user guide NILFISK SCRUBTEC 743
Detailed instructions for use are in the User's Guide.
[. . . ] 6, 760, 947 READ THIS BOOK
SCRUBTEC 743 S SCRUBTEC 743 L SCRUBTEC 751 S SCRUBTEC 751 L SCRUBTEC 743 S C SCRUBTEC 743 L C
CAUTION: Read the Operator's Manual before using the appliance. This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. [. . . ] Neutralize any acid spills with ammonia or bicarbonate of soda.
-16-
Figure 14
Figure 15
Page
CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751
How To Prepare the Machine For Operation
How To Charge The Batteries WARNING: Charging the batteries in an area without adequate ventilation could result in an explosion. To prevent an explosion, charge the batteries only in an area with good ventilation. Remove power to the control panel by pressing the red "OFF" button. If the machine is equipped with a key switch, turn the key counterclockwise to the "OFF" position. Before charging the batteries, the battery compartment needs to be vented. WARNING: Before raising or removing the recovery tank, be sure tank is empty. Do not operate or perform maintenance on the machine while the recovery tank is in the open position. The Scrubtec is equipped with an on-board charger located behind the recovery tank (See Figure 17). The AC power cord to the on-board charger is located in its storage compartment under the control handle at the rear of the machine (See Figure 16). Connect the charger to a properly grounded single phase (3-wire) wall receptacle. NOTE: When the charger is plugged into the wall receptacle, the yellow light will be illuminated on the control panel next to the plug symbol and the charger with begin charging (see figure 3, item A). 3-Stage Charging Sequence: · Bulk Stage - In the bulk stage of charging, the red light is illuminated on the charger (See Figure 17). During this stage the charger is supplying its full amp output to the batteries. It will continue to charge the batteries at this rate until the batteries reach approximately 75% of their capacity.
CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751
Figure 16
Figure 17
Page -17-
How To Prepare the Machine For Operation
· Absorption Stage - In the absorption stage the red and green light will be illuminated on the charger (See Figure 17). During this stage the charger maintains constant voltage and lets the batteries absorb the charge at their own rate. · Float and Maintenance Stage - In the maintenance stage the red light turns off and only the green light will be illuminated on the charger (See Figure 17. During this stage the charger applies a lower, closely regulated voltage to maintain full charge and prevents discharge. Unplug charger power cord from the wall outlet before powering up control panel on machine. Store the charger power cord in the storage compartment located under the control handle (See Figure 16). Unlatch and stow prop rod back in solution tank and close recovery tank after charging has been completed.
NOTE: It is not necessary to remove the brush housing assembly when removing or installing the brush or pad driver. For greater access to the brush or when driving the machine up a ramp, the brush housing assembly can be removed. To remove brush housing assembly, pull outward on the spring loaded pin on the left side of the housing, then lift the brush housing assembly up and outward (See Figure 18). [. . . ] Failure to comply with the six-month inspection requirement or failure to replace worn motor brushes identified during the inspection will void the warranty on the motors. Cost of the six-month inspection and replacement of carbon motor brushes is the responsibility of the purchaser. In the event of a warranty claim on the motors, proof of inspection and any required motor brush replacement must be provided. This warranty is extended only to the original purchaser for use of the product. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NILFISK SCRUBTEC 743
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NILFISK SCRUBTEC 743 will begin.