User manual NILFISK SCRUBTEC BOOST R
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NILFISK SCRUBTEC BOOST R. We hope that this NILFISK SCRUBTEC BOOST R user guide will be useful to you.
You may also download the following manuals related to this product:
NILFISK SCRUBTEC BOOST R (2085 ko)
NILFISK SCRUBTEC BOOST R (2085 ko)
NILFISK SCRUBTEC BOOST R (2244 ko)
NILFISK SCRUBTEC BOOST R (10696 ko)
NILFISK SCRUBTEC BOOST R (2244 ko)
NILFISK SCRUBTEC BOOST R (2244 ko)
NILFISK SCRUBTEC BOOST R (10696 ko)
NILFISK SCRUBTEC BOOST R (10696 ko)
NILFISK SCRUBTEC BOOST R (1569 ko)
NILFISK SCRUBTEC BOOST R (1569 ko)
NILFISK SCRUBTEC BOOST R (1569 ko)
NILFISK SCRUBTEC BOOST R (2085 ko)
NILFISK SCRUBTEC BOOST R (2244 ko)
NILFISK SCRUBTEC BOOST R (1569 ko)
NILFISK SCRUBTEC BOOST R (10696 ko)
Manual abstract: user guide NILFISK SCRUBTEC BOOST R
Detailed instructions for use are in the User's Guide.
[. . . ] Pour enlever la brosse / plateau support disque, il suffit de soulever la tête en appuyant sur la pédale (11), puis appuyer sur le bouton-poussoir (75) et attendre jusqu'à ce que la brosse / plateau support disque tombe au sol. REMARQUE Pour un lavage / séchage correct du sol près du mur, Nilfisk Alto recommande d'approcher le côté droit de la machine, comme illustré dans la figure 3. The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal. [. . . ] The machine can be supplied in one of the following modes: A) Batteries (WET or GEL) already installed and ready to be used 1. Check that the batteries are connected to the machine with the connector (12). If the green warning light (81a) turns on, the batteries are ready to be used. If the yellow or red warning light (81b or 81c) turns on, the batteries must be charged (see the procedure in Maintenance chapter). batteries (WET) installed on the machine , but without electrolyte 1. Open the cover (22) and check that the recovery tank (21) is empty, otherwise empty it with the drain hose (16). If it comes in contact with skin or eyes, rinse thoroughly with water and consult a physician. Fill up the battery cells with sulphuric acid for batteries (density 1. To avoid damaging the floor, dry with a cloth both acid and water on the top of the batteries after charging. Let the batteries rest and fill in with sulphuric acid as shown in the Battery Manual. Set the machine and the battery charger (if equipped) according to the type of batteries installed (WET or GEL) as shown in the following paragraph. Fill the tank (45) with a detergent suitable for the work to be performed (highly concentrated detergent). Do not fill the detergent tank completely, leave a few inches from the edge. , wait for the hoses to fill up, before starting the Chemical Mixing System. Check that the green warning light (81a) turns on (charged batteries). If the yellow or red warning light (81b or 81c) turns on, turn the ignition key back to "0" and charge the batteries (see the procedure in Maintenance chapter). drive the machine to the working place: · By pushing it with the hands on the handlebar (2) (only for SCRUBTEC 545B and 553B). By pushing it with the hands on the handlebar (2) and pressing the switch (83) to move forward, or pressing the switch (83) together with the switch (78) to move rearward (only for SCRUBTEC 545BL, 553BL and BOOST 5). If it is necessary to use the vacuum system only, stop the brush/pad-holder and the vacuum system with the switch (71), and press the vacuum system switch (73). NOTE To move the machine forward, press either the left or right switch (83) or both. Turn off the brush/pad-holder and the vacuum system with the switch (71). If necessary, press the washing water flow control switches (82) as necessary, depending on the type of cleaning to be performed. [. . . ] Check that the front corner (J) of the rear blade is not worn; otherwise, overturn the blade to replace the worn corner with an integral one. If the other corners are worn too, replace the blade according to the following procedure: · Unscrew the handwheels (I) and remove the retaining strip (L), then replace the front blade (C). It is advisable to wear protective gloves when cleaning the brush/pad because there may be sharp debris. Wash with clean water the cover (A), the tanks (B and C) and the vacuum grid with automatic shut-off float (D). [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NILFISK SCRUBTEC BOOST R
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NILFISK SCRUBTEC BOOST R will begin.