User manual NILFISK SCRUBTEC 233
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual NILFISK SCRUBTEC 233. We hope that this NILFISK SCRUBTEC 233 user guide will be useful to you.
You may also download the following manuals related to this product:
NILFISK SCRUBTEC 233 (2588 ko)
NILFISK SCRUBTEC 233 (2460 ko)
NILFISK SCRUBTEC 233 (2659 ko)
NILFISK SCRUBTEC 233 (2588 ko)
NILFISK SCRUBTEC 233 (2453 ko)
NILFISK SCRUBTEC 233 (2592 ko)
NILFISK SCRUBTEC 233 (2460 ko)
NILFISK SCRUBTEC 233 (2460 ko)
NILFISK SCRUBTEC 233 (2659 ko)
NILFISK SCRUBTEC 233 (2659 ko)
NILFISK SCRUBTEC 233 (2659 ko)
NILFISK SCRUBTEC 233 (2588 ko)
NILFISK SCRUBTEC 233 (2588 ko)
NILFISK SCRUBTEC 233 (2588 ko)
NILFISK SCRUBTEC 233 (2592 ko)
NILFISK SCRUBTEC 233 (2592 ko)
NILFISK SCRUBTEC 233 (2592 ko)
NILFISK SCRUBTEC 233 (2453 ko)
NILFISK SCRUBTEC 233 (2453 ko)
NILFISK SCRUBTEC 233 (2453 ko)
NILFISK SCRUBTEC 233 MANUAL 2 (2460 ko)
Manual abstract: user guide NILFISK SCRUBTEC 233
Detailed instructions for use are in the User's Guide.
[. . . ] Before performing any procedure on the machine, the operators and qualified technicians must read this Manual carefully. Alto will not be answerable for damages coming from the non-observance of this prohibition. The User Manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause damage to it. The declaration of conformity, supplied with the machine, certifies the machine conformity with the law in force. [. . . ] BAT BE BRK BZ1 C1 C2 C3 CH CS CSC EB1 EB2 EB3 EB3/2 EV1 F1 F2 F3 F4 K1 LD1 M1 M2 M3 M4 M5 24 V batteries Flashing light Electromagnetic brake Reverse gear warning buzzer/horn Battery connector Battery charger auxiliary connector Battery charger external fan auxiliary connector Battery charger Brush deck connector Cylindrical brush deck sub-connector Function electronic board Drive system electronic board Electronic board under the control panel Electronic board under control panel (optional) Solenoid valve Function electronic board fuse Drive system electronic board fuse Low power circuit fuse Pump fuse (optional) Ignition switch Drive system electronic board diagnostic LED Left brush motor Right brush motor Vacuum system motor Brush deck actuator Drive system motor M6 M7 M8 M9 PR1 RV1 RV2 SW0 SW1 SW2 SW3 SW4 SW5 SW6 Squeegee actuator Washing water pump (optional) Detergent pump (optional) Cooling fan Washing water level sensor Working speed potentiometer (if equipped) Speed potentiometer (pedal) Emergency push-button Actuator position 0 microswitch Actuator position 1 microswitch Actuator position 2 microswitch Steering sensor Driver's seat microswitch Reverse gear switch On some points of the machine there are some adhesive plates indicating: DANGER WARNING CAUTION CONSULTATION While reading this Manual, the operator must pay careful attention to the symbols shown on the plates. Do not cover these plates for any reason and immediately replace them if damaged. Turn off the machine by turning the ignition key (41) to "0". Press and hold the switch (36), then turn on the machine by turning the ignition key (41) to "I". Release the switch (36) at least 5 seconds after starting the machine. Within three seconds, press the switch (36) again for a few seconds and check that the warning light for the required setting is flashing. Turn the selector (C) to WET or GEL according to the type of batteries installed. Open the covers (51 and 58) and check that the tanks (60 and 61) are empty, otherwise empty them through the drain hose (10) and the tap (24). If a battery box is installed, place it on the left side of the machine, to allow the tank assembly (71) to be closed correctly. When starting the machine, check that between the deck (4 or 5) and the machine, or between the squeegee (12) and the machine, there is no foreign material which may prevent the deck or squeegee from lifting. This check is necessary because, if the machine has been turned off without lifting the deck and the squeegee, the deck and the squeegee will lift automatically at next machine start-up. It is not necessary to lock the machine during stopping or parking, because the electromagnetic brake (27) turns on automatically when the gear pedal is not pressed. NOTE For correct scrubbing/drying of floors at the sides of the walls, Alto suggests to go near the walls with the right side of the machine as shown in figure 2. If necessary, stop the machine and turn the squeegee adjusting handwheel (16) so that the rear blade touches the floor along all its length. To avoid any damage to the floor surface, turn off the brushes/pad-holders when the machine stops in one place, especially when the extra pressure function is on. Working with brush/pad-holder extra pressure function turned on NOTE When the cylindrical brush deck is installed, the extra pressure function is not enabled. If the floor proves to be particularly difficult to clean, it is possible to turn on the brush/pad-holder extra pressure function by pressing the switch (35). The switch (35) is enabled only when the deck (4) is lowered and the switch warning light (34) is on. In case of brush/pad-holder motor overload, due to foreign bodies which prevent them from rotating, or to excessively aggressive floors/brushes, the safety system stops the brushes/pad-holders after about one minute of continuous overload. The overload is shown by the three warning lights (37a, 37b, 37c) flashing simultaneously. If the overload takes place when the extra pressure function is on, the system automatically reduces the pressure on the brushes/pad-holders, thus turning the extra pressure function off. To start scrubbing again after a brush/pad-holder stop due to overload, stop the machine by turning the ignition key (41) to "0". [. . . ] Remove the transparent cover (A), then remove the filter strainer (E) under the machine, in front of the right rear wheel. NOTE The filter strainer (B) must be correctly positioned on the housing (D) of the support (C). NOTE Charge the batteries when the yellow or red warning light (37b or 37c) turns on, or at the end of every working cycle. When the batteries are discharged, charge them as soon as possible, as that condition makes their life shorter. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE NILFISK SCRUBTEC 233
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual NILFISK SCRUBTEC 233 will begin.