User manual NOVAK GOAT 3S BASIC SETUP GUIDE

[. . . ] transmitter adjustments ·NOT ALL TRANSMITTERS HAVE THESE ADJUSTMENTS· trouble-shooting guide steering channel works but motor will not Run ·Red & Green status LEDs on solid­­Check input signal harness connections at ESC and receiver. ·Red status LED on solid & Green LED blinking­­Check motor sensor harness connection. Possible ESC shut-down due to locked rotor detection­­return throttle to neutral position to regain motor control­­check vehicle's drive train for free operation. Possible ESC thermal shut-down­­Check gear ratio & free operation of drive train for possible overloading/ESC is being severely overloaded­­allow system to cool & return throttle to neutral position to regain motor control. [. . . ] 4. 5" harness in Novak kit #5315, and 9. 0" harness in Novak kit #5320. low-loss powER connEctoRs­3. 5mm [Novak kit #5731] Low-Loss connectors generate dozens of wiring routing and installation options. 3-amp hIGh-voltaGE UnIvERsal bEc [Novak kit #5463] 30x30x6mm coolInG Fans [Novak kits #5648 & #5652] Replacement BEC regulates voltage output and is required for use with 3S Li-Po batteries. Included cooling fan fits ESC's heat sink perfectly & has power plug for easy connection. Single fan in Novak kit #5648, and 2-pack of fans in Novak kit #5652. *Check Novak's Web site for additional information. FIGURE 8 raised metal barb service procedures Before sending your speed control in for service, review the Trouble-Shooting guide and instructions. After reviewing instructions, if you feel that your ESC requires service, please obtain the most current product service options and pricing by the following ways: section of the Web site. Fill out the needed information on this form and return it with the Novak product that requires servicing. PHONE/FAX: If you do not have access to the internet, please contact our customer service department by phone or fax. PRODUCT SERVICE FORM & include a valid cash register receipt with purchase date and dealer name & phone # on it, or an invoice from previous service. If warranty provisions have been voided, there will be service charges. NOVAK bRuSHLESS MOTORS ONLy bRUshlEss EXtEnsIon haRnEssEs [Novak kits #S5357 & #S5358] Optional harnesses are available in two lengths (4" in Novak kit #S5357 & 9" in Novak kit #S5358). NO REVERSE VOLTAGE! pOWER TRANS-CAp MODuLE REQuIRED TRANSMITTER ON FIRST product warranty The Goat 3S Brushless/Brush ESC is guaranteed to be free from defects in materials or workmanship for a period of 120 days from the original date of purchase (verified by dated, itemized sales receipt). This product is not intended for use by children under 14 years of age without the strict supervision of an adult. Use of this product in an uncontrolled manner may result in physical damage or injuries--take extra care when operating any remote control vehicle. · All Rights Reserved · No part of these instructions may be reproduced without the written permission of Novak Electronics, Inc. · Goat 3S ESC, Smart Braking II, Polar Drive Technology, Radio Priority Circuitry & One-Touch Set-Up are all trademarks of Novak Electronics, Inc. WEB SITE: Print a copy of the PRODUCT SERVICE FORM from the CUSTOMER SERVICE GOOD QuALITy Li-po bATTERIES SuGGESTED WARRANTy SERVICE: For warranty work, you MUST CLAIM WARRANTY on GOOD QuALITy RADIO SySTEM SuGGESTED NOVAK ELECTRONICS, INC. P: (949) 833-8873 · F: (949) 833-1631 customer service E-mail: cs@teamnovak. com www. teamnovak. com P4 · ESCs returned without a serial number will not be serviced under warranty · ADDITIONAL NOTES: ·Dealers/distributors are not authorized to replace products thought to be defective. ·Ifahobbydealerreturnsyourproductforservice, submitacompletedPRODUCT SERVICE FORM to the dealer and make sure it is included with product. ·NovakElectronics, Inc. doesnotmakeanyinternalelectroniccomponents(transistors, resistors, etc. ) available for sale. DO NOT buNDLE pOWER & SIGNAL WIRES TOGETHER RF noise in the power wires can adversely effect radio system performance. Always insulate exposed wiring with heat shrink tubing or electrical tape to prevent short circuits. Exposure to CA glue or its fumes can cause damage to internal components of the ESC and result in premature failure. INSuLATE WIRES NO CA GLuE P1 step 1­connect The Goat 3S has a user-replaceable input harness with the industry-standard receiver connector on it & works with all major radio brand's new receivers (Refer to Figure 1 to see how to connect the included user-replaceable input harness to Novak's XXtra Synthesized FM Receiver: 75 Mhz). However, some very old receivers must have the wiring sequence in the plastic 3-pin JST connector housing changed on the receiver end. This is important, as the receiver & servo electronics may be damaged if the sequence is incorrect. For instructions on changing the wiring sequence for older receivers, visit the Novak Web site. input harness step 3­wirinG speed control to motor bRuSH-typE mOtOrS (Fig. motoR capacItoRs The Goat 3S ESC automatically switches to Brush-Mode when the ESC's power is switched ON and no brushless motor sensor harness is connected. Electric brush-type motors generate RF noise that causes interference. [. . . ] If Power Trans-Cap Module becomes dented or damaged, ESC failure can occur--replace immediately (Novak kit #5686). Novak brushless motors do not require external motor capacitors. bRuSHED mOtOr precautions FACTORy-INSTALLED pOWER TRANS-CAp MODuLE REQuIRED The factory-installed Power Trans-Cap Module MUST be used with brush-type motors. If Power Trans-Cap Module becomes dented or damaged, ESC failure can occur--replace immediately (Novak Kit #5686). REtURn tRansmIttER thRottlE to nEUtRal Red status lEd will turn solid red, indicating that speed control is at neutral and that proper programming has been completed. [. . . ]