User manual OPTOMA H56

[. . . ] Table of Contents Usage Notice Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 English Introduction Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After pressing the Power/Standby button, you will see a message Power off the lamp?Power/Standby LED indicator will light solid amber for about 30 seconds. After the Power/Standby indicator starts flashing, you can turn off the main power switch on the side of the projector. If you want to turn on the projector, you must press the Power/Standbybutton within 90 seconds of the start of the indicator flashing. Do not turn on the projector immediately following a power off procedure. v When the LAMP indicator flashes green for about 10 seconds, you will see a message Fan Fail on the on-screen display. Please contact your local reseller or service center. v When the TEMP indicator lights solid orange, it indicates the projector has been overheated. Under normal conditions, the projector can be switched on again for your presentation. If the problem persists, you should contact your local reseller or service center. 12 Installation Adjusting the Projected Image Adjusting the Projector Height The projector is equipped with an elevator foot for adjusting the projector height. To raise the projector: 1. Raise the projector to the desired display angle , then release the button to lock the elevator foot into position. Lower down the projector, then release the button to lock the elevator foot into position. Use to fine-tune tilt-adjustment. 1 English Elevator Button 3 2 Elevator Foot 13 English Installation Adjusting the Projector Zoom / Focus You may adjust zoom ring to zoom in / out. Rotate the zoom ring counter-clockwise to zoom in and clockwise to zoom out. The projector will focus at distances from 3. 74 feet to 32. 81 feet (1. 14m to 10. 00m). Zoom Ring Focus Ring Adjusting Projection Image Size Screen Max. Max. (WxH) Screen Size Min. (WxH) Distance 28. 1" 23. 4" 22. 48" x 16. 86" 18. 72" x 14. 04" 3. 74' 73. 8" 61. 5" 59. 04" x 44. 28" 49. 20" x 36. 90" 9. 84' 123. 0" 102. 5" 98. 4" x 73. 8" 82. 00" x 61. 50" 16. 4' 172. 2" 143. 5" 137. 76" x 103. 32" 114. 80" x 86. 10" 22. 97' 221. 5" 184. 5" 177. 20" x 132. 90" 147. 60" x 110. 70" 29. 53' 246. 1" 205. 1" 196. 88" x 147. 66" 164. 08" x 123. 06" 32. 81' vThis graph is for users reference only. 14 User Controls Panel Control & Remote Control There are two ways for you to control the functions: Remote Control and Panel Control. English Panel Control Remote Control Use the Remote Control Backlit 4 When you press Backlit button, all buttons on remote Power controller will flash fluorescent yellow. Return to normal mode, press Backlit button again. 4 Refer to the Power On/Off the Projector section on page 11~12. Four Directional Select Keys 4 Use Enter your selection. to select items or make adjustments for 4 Confirm your selection of items. While making selection on a particular icon, press Enter w To exit the OSD, press the Menu button. key to select the key. 4 When sub-menu is displayed, press required item and adjust the settings by w To go to main menu, press the Menu button. key to adjust the parameter or required func- 4 After using tion in the items of the sub-menu, press Enter button to confirm your change and the screen will be back to the sub-menu at once. w Press the Menu button to go back sub-menu. If you dont press Enter button to confirm your change and exit the screen at once, the items will not to be modified. Item Main menu Sub-menu 18 User Controls Menu Tree PICTURE. . . . . . . . . . . . . . . Mode Contrast Brightness Color Tint Sharpness Gamma Reset IMAGE. . . . . . . . . . . . . . . . . . . White Peaking Color Temp Image Mode Advanced Adjustment Signal De-Interlacing Reset Current/All 1/2/3 Film/Video/Graphics/PC R Contrast/G Contrast/B Contrast/ R Brightness/G Brightness/ B Brightness Horizontal/Vertical/Frequency/ Phase Auto/Film Current/All SYSTEM. . . . . . . . . . . . . . . . . Language Bulb Auto Image Auto Shutdown Blanking DISPLAY. . . . . . . . . . . . . . . [. . . ] If you use a PC: If the resolution of your computer is higher than 1024 x 768. In the Windows Program Manager, click the Windows Setup icon in the Main group. Verify that your display resolution setting is less than or equal to 1024 x 768. Open My Computer icon, the Control Panel folder, and then double click the Display icon. [. . . ]