User manual OREGON SCIENTIFIC BAR638HGA

[. . . ] LED status indicator WEAK SIGNAL NO SIGNAL To force a manual search for clock signals, press and hold for 2 seconds. If you are using more than one sensor, select a different channel for each sensor. PRODUCT OVERVIEW FRONT VIEW TIME ZONES When the main unit receives an atomic clock signal for the first time, or when you force a manual search for the atomic clock reception, the time will automatically be set to Pacific time (PA). To change to another time zone (MO - Mountain, CE - Central or EA - Eastern) simply: 1. 4. Wall mount hole RESET hole CHANNEL number (1-3) Battery compartment (Battery compartment cover not shown) 3. [. . . ] You may need to experiment with various locations to get the best results. The reception icon shown in the Temperature and Humidity Areas show the status. BACK VIEW NOTE It is recommended that you use alkaline batteries with this product for longer performance. UNIT Main Remote LOCATION Indoor Temperature / Humidity Area Outdoor Temperature / Humidity Area SWITCH CLOCK DISPLAY Press MODE to toggle between Clock with Seconds and Clock with Weekday display. ALARM This product is equipped with a 2-minute crescendo alarm. Installing the batteries: 1. MEM : View current, maximum and minimum temperature and humidity readings 3. : Press to activate or deactivate alarm LCD DISPLAY LCD DISPLAY VIEW ALARM SETTINGS . The alarm time and alarm status will show in the Press Clock Area. SET ALARM 1. Press to confirm. ACTIVATE ALARM Press to activate or deactivate the alarm. shows in the Clock / Alarm Area when the alarm is activated. 1 2 3 4 5 6 7 8 9 10 11 1. Moon Phase SILENCE ALARM When the alarm time is reached, the crescendo alarm will sound for 2 minutes. To silence the alarm: · Press SNOOZE to silence it for 8 minutes. OR · Press any key except SNOOZE to mute the alarm and activate it again after 24 hours. If no button is pressed, the alarm will automatically silence after 2 minutes. It will then sound again after 8 minutes. 12 13 ICON TABLE STAND DESCRIPTION Main unit is searching for sensors. Channel 1 is selected (number will change depending on the sensor you select). 14 15 16 --- shows in Outdoor The selected sensor cannot Temp / Humidity Area be found. Search for the sensor or check batteries. WEATHER FORECAST This product forecasts the next 12 to 24 hours of weather within a 30-50 km (19-31 mile) radius with 70 to 75 percent accuracy. The weather forecast is always displayed. SEARCH FOR SENSOR To search for a sensor, press and hold MEM and CHANNEL (on the main unit) for 2 seconds. NOTE If the sensor is still not found, check the batteries, obstructions, and remote unit location. NOTE Signals from household devices such as doorbells, electronic garage doors, and home security systems may cause temporary reception failure. The reception will resume once the interference ends. SUNNY PARTLY CLOUDY CLOUDY RAINY TEMPERATURE AND HUMIDITY This product can display current, minimum, and maximum temperature and humidity percentage information collected by the remote sensors and main (indoor) unit. BAR638HGA_M_SINGLE_USA. p65 1 2005. 6. 29, 3:34 PM Outdoor data is collected and displayed every 40 seconds. Indoor data is collected and displayed every 10 seconds. Temp Remote sensor Shows "LLL" or "HHH" Cannot locate remote sensor Cannot change channel Data does not match main unit Temperature is out-of-range Check batteries Check location Check sensors. Only one sensor is working Initiate a manual sensor search reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The website also includes contact information for our Customer Care department in case you need to reach us, as well as frequently asked questions and customer downloads. We hope you will find all the information you need on our website, however if you're in the US and would like to contact the Oregon Scientific Customer Care department directly, please visit: www2. oregonscientific. com/service/support OR Call 1-800-853-8883. For international enquiries, please visit: www2. oregonscientific. com/about/international FCC STATEMENT TROUBLESHOOTING PROBLEM SYMPTOM Calendar Clock Strange date / month Cannot autosynchronize the date and time REMEDY Change language This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. [. . . ]