User manual OREGON SCIENTIFIC RAR601

[. . . ] 6 Setup Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Search for Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Set Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Clock / Alarm Area : Time, day of week, month, date, alarm : Press to increase setting : Press to decrease setting MODE : Press to change display / settings MEM : Press to view current or max / min temperature readings ((. )) : Press to view alarm settings, activate alarm 2. 8. 5 6 7 MEM 8 3 RAR601 lab test R2 3 1/17/04, 4:47 PM EN EN BACK VIEW 1. 5. Wall mount Battery compartment °C / °F switch RESET hole Table stand 4 RAR601 lab test R2 4 1/17/04, 4:47 PM REMOTE SENSOR 1 1 2, 3 1. LED Status indicator 1. 3. Wall mount hole Battery compartment Battery compartment cover 5 RAR601 lab test R2 5 1/17/04, 4:47 PM EN EN GETTING STARTED BATTERIES Batteries are not supplied with this product. You will need to purchase 2 x UM-4 (AAA) 1. 5V alkaline batteries for the main unit, and 2 x UM-3 (AA) 1. 5V alkaline batteries for the remote sensor. Insert batteries before first use, matching the polarity as shown in the battery compartment. For best results, install batteries in the remote sensor before the main unit. Press MODE to confirm. TABLE STAND OR WALL MOUNT Insert the stand on the back of the product, or mount it on a wall with a nail. shows when batteries are low. UNIT Main Remote LOCATION Indoor Temperature Area Outdoor Temperature Area. REMOTE SENSOR This product is shipped with a Sensor that collects temperature readings. Only one sensor can be used with this product. 6 RAR601 lab test R2 6 1/17/04, 4:47 PM SETUP SENSOR 1. Open the remote sensor battery compartment with a small Phillips screwdriver. Insert the batteries, matching the polarity as shown in the battery compartment. Press RESET on the main unit to initiate signal sending between the sensor and the main unit. The reception icon on the main unit will blink for approximately 3 minutes while it is searching for the sensor. (Refer to the Sensor Data Transmission section for more information. ) Close the remote sensor battery compartment. Secure the sensor in the desired location using the wall mount or table stand. For best results: · Insert the batteries before you mount the sensor. · Do not place the sensor more than 30 meters (98 feet) from the main (indoor) unit. · Position the sensor so that it faces the main (indoor) unit, minimizing obstructions such as doors, walls, and furniture. · Place the sensor in a location with a clear view to the sky, away from metallic or electronic objects. · Position the sensor close to the main unit during cold winter months as below-freezing temperatures may affect battery performance and signal transmission. You may need to experiment with various locations to get the best results. The reception icon shown in the Outdoor Temperature Area shows the status. 4. [. . . ] · Remove the batteries if storing this product for a long period of time. The technical specification of this product and contents of this user guide are subject to change without notice. Images not drawn to scale. SAFETY AND CARE Clean the product with a slightly damp cloth and alcoholfree mild detergent. Avoid dropping the product or placing it in a high-traffic location. 10 RAR601 lab test R2 10 1/17/04, 4:47 PM TROUBLESHOOTING Check here before contacting our customer service department. [. . . ]