User manual PACOM PDR-4LX

[. . . ] Four-Channel Digital Video Recorder WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. COMPLIANCE NOTICE OF FCC: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. [. . . ] Refer to the device manufacturer's documentation for Line Delimiter character(s). Use the virtual keyboard to enter Highlight the box beside Ignore String, and press the the strings of text that you want the DVR to ignore. Refer to the device manufacturer's documentation for text strings that the device sends during transactions, so you will know which ones you do not want recorded. NOTE: When setting up the EPSON-POS device, the user cannot change Line Delimiter and Ignore String parameters. Highlight the box beside Transaction Timeout, and set the length of time to wait for the new text string. The DVR will consider a transaction ended if there is no text sting during timeout dwell time after the last text input string. Highlight the box beside Display Dwell, and set the length of time you would like to display text-in data. Highlight the Case Sensitive box and press the button to toggle between On and Off. Refer to the device manufacturer's documentation to determine if the text strings are Case Sensitive. If the device distinguishes between upper and lower case letters, make certain the Case Sensitive box is turned On. Alarm Out Setup Screen The Alarm Out setup screen allows you to establish a schedule for each alarm output from the DVR. Figure 42 -- Alarm Out setup screen. Each alarm output can be given its own title by highlighting the box under the Title heading and button. pressing the 31 User's Manual Highlighting the Sched field and pressing the button opens a schedule screen. You can schedule alarm output in 30-minute increments from 0:00 to 24:00. Figure 43 -- Alarm Out Schedule screen. You can select individual blocks of time, entire days of the week, entire blocks of time or the entire schedule. Select an entire day by highlighting the day of the week or Holiday on the left of the screen. Select an entire block of time by highlighting the time at the top of the screen. Select the entire screen by highlighting the empty box in the upper button from No Arming (no block) to On (blue block) to left corner of the screen. When set to Event, the Alarm Out is only active when there is an Event during the scheduled time. Audio Setup Screen Highlight Audio in the Main menu and press the button. The Audio Setup screen appears. Figure 44 -- Audio Setup screen. 32 Four-Channel Digital Video Recorder Highlight the box beside Audio Recording and press the button. When it is On, the DVR will play live audio through the attached speaker when it displays live video. Move to the Audio In field, and highlight the box under On/Off heading, and press the button. You can save your changes by highlighting OK and pressing the the screen without saving the changes. Selecting Cancel exits NOTE: The DVR will NOT record audio when the recording speed is set to less 15 ips (12. 5 ips for PAL). The DVR may not record audio depending on the Transfer Speed when the RAS (Remote Administration System) Watch application program is connected. RS232/RS485 Setup Screen The RS232/RS485 setup screen allows you to set up the RS-232C and RS-485 ports to communicate with external devices such as remote controls and dome cameras. Figure 45 -- RS232/RS485 setup screen. [. . . ] Choose the appropriate letter corresponding to the USB-IDE hard disk drive. Create DOS partition or Logical DOS Drive. " 73 User's Manual 10. In the Create DOS Partition or Logical DOS Drive menu, choose "1. Create Primary DOS Partition. " And Type "Y" to use all available space and hit the enter key. [. . . ]