User manual PALSONIC TFTV760

[. . . ] requirement of environment temperature; -200C~500C for storage; 00C~400C for working. The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the the manufacturer's instructions are followed. [. . . ] If you want to go to TV mode, press AV button repeatedly to select TV mode. Press ENTER to cancel OSD. Bass - Treb- 16 Channel Preset CHANNEL SETTING Auto search Search Fine Tune Change Prog Current Prog Change to Prog Skip 12 15 ON <V-> or V+> key to change To enter into CHANNEL SETTING menu 1. Press VOL+ or VOL- button to confirm or adjust selected item. Auto Search POWER CH VOL - VOL + CH ENTER Please enter into CHANNEL SETTING menu and select Auto Search item. Press VOL- or VOL+ button to start Auto Search and all active programs will be memorised. 10 During the process of Auto Search, pressing VHFL MENU button will stop Auto Search. MENU Notes: Press <Menu> to escape C. SYS ZOOM CLK SLP Please confirm the sound system is correct according to your area before Auto Searching. AUTO. ADJ P. M DSP Manual Search 1 4 7 AV 2 5 8 0 OSD POSITION Bass+ 3 6 9 -/-Treb+ STILL Use manual search function if desired channels cannot be preset or if you would like to preset channels to specific position numbers one by one. Use 0~9 digit buttons or CH / buttons to select a position number firstly, then enter into CHANNEL SETTING menu and select Search Channel searching. . Press VOL+ button to enter Channel Press <V->/<V+> to search channel Search sub-menu, then press VOL+ or VOL- to Press <P->/<P+> to shift band start manual search. Press MENU button can exit Channel Search sub-menu. Bass - Treb- Fine Tuning In area of inferior broadcast conditions where adjustment is necessary for a better picture and sound, use Fine tuning. Use 0~9 digit buttons or CH / buttons to select the desired channel, then enter into Fine Tuning. . Press VOL+ button to enter into Fine Press <Menu> to change tuning sub-menu, then press and hold VOL+ or VOL- to start Fine tuning. 17 Channel Preset (continued) CHANNEL SETTING Auto search Search Fine Tune Change Prog Current Prog Change to Prog Skip 12 15 ON <V-> or V+> key to change Channel Skipping You can skip unnecessary channels by using Skip function when you browse program by CH / buttons. Use 0~9 digit buttons or CH / buttons to select a unwanted channel firstly, then enter into CHANNEL SETTING menu and select Skip item. Now this channel will be skipped when you browse channels with CH / button. To restore the skipped channel, please select the skipped channel with 0~9 digit buttons and then enter the CHANNEL SETTING menu, select Skip item and press VOL+/- to set Skip to OFF. POWER CH VOL - VOL + CH ENTER Channel Edit After Auto Channel Preset, this function is for you to edit the order of programs conveniently according to your favourite. Please enter into CHANNEL SETTING CHANNEL SETTING Auto search menu and select Change to Prog item by Search CH / buttons, press VOL+/- button to Fine Tune Change Prog select a target channel to exchange with 12 Current Prog current channel. Then select Change 15 Change to Prog ON Skip Prog item and press VOL+/- to confirm. Now the program in current channel <V-> or V+> key to change number exchanges with the program in the target channel number. MENU C. SYS ZOOM CLK SLP AUTO. ADJ P. M DSP 1 4 7 AV 2 5 8 0 OSD POSITION Bass+ 3 6 9 -/-Treb+ STILL Bass - Treb- 18 Channel Select Use 0~9 digit buttons and -/-- button Use 0~9 digit buttons to select one-digit channel number. Press -/-- button to display "-". - 8 Press 0-9 direct channel selector. 8 POWER To select two-digit channel: CH VOL VOL - + CH ENTER Press -/-- button repeatedly to display "--". - - Press 1-9 buttons. -1 Press 0-9 buttons. 18 MENU C. SYS ZOOM CLK SLP AUTO. ADJ P. M DSP To select three-digit channel: Press -/-- button repeatedly to display "--". 180 1 4 7 AV 2 5 8 0 OSD POSITION Bass+ 3 6 9 -/-Treb+ Using CH Press CH Press CH / button STILL button, the channel number increases; button, the channel number decreases. Bass - Treb- Use previous channel button Press this button to switch between the current channel and previous channel. 19 Picture Adjustment PICTURE SETTING Brightness Contrast Color + + + + + 50 50 50 50 50 Adjusting picture 1. Press VOL+/- button to adjust the selected item. Sharpness Tint <V-> or V+> key to change Item POWER VOLdarker weaker paler softer purplish VOL+ lighter stronger deeper sharper greenish CH VOL - VOL Bright Contrast Saturation Sharpness Tint* + CH ENTER MENU * Note: The item Tint is for NTSC only. Press the P. M button to select a picture mode according to your favourites. There are four picture mode: Bright, Standard, Mild and User mode. C. SYS ZOOM CLK SLP AUTO. ADJ P. M DSP 1 4 7 AV 2 5 8 0 OSD POSITION Bass+ 3 6 9 -/-Treb+ Using STILL button You can still current screen picture by pressing STILL button on the remote. Press this button again to resume. STILL Using AUTO. ADJ button When wrong picture identification occurs, you can use AUTO. ADJ button on the remote to obtain a correct picture. Bass - Treb- 20 Sound SOUND Bass Treble Balance <V-> or V+> key to change + + + 25 25 25 Adjusting Sound 1. Item Bass Treble Balance VOLweaker weaker decreases the right channel VOL+ stronger stronger decreases the left channel POWER CH VOL - VOL + CH ENTER Notes: You can quickly adjust Bass and Treble by using Bass+/Bassand Treb+/Treb- buttons on the remote. MENU C. SYS ZOOM CLK SLP AUTO. ADJ P. M DSP Adjusting Volume 1 4 7 AV 2 5 8 0 OSD POSITION Bass+ 3 6 9 -/-Treb+ You can use VOL+ or VOL- button to adjust volume. [. . . ] Now you can adjust phase and frequency to obtain the best display. PICTURE SETTING Brightness Contrast Phase Frequency USER_R USER_G USER_B Color Temp 9300K + + + + + + + 25 25 25 25 25 25 25 MENU C. SYS ZOOM CLK SLP <V-> or V+> key to change AUTO. ADJ P. M DSP Adjusting Colour temperature 1 4 7 AV 2 5 8 0 OSD POSITION Bass+ 3 6 9 -/-Treb+ You can select different Colour temperature to obtain correct white. Press MENU button, use CH / to select Color Temp item, press the VOL+/- to select between User, 9300K, 7300K, 6500K. The USER_R, USER_G and USER_B can not accessed and adjusted unless you set Color Temp to "User". PICTURE SETTING Brightness Contrast Phase Frequency USER_R USER_G USER_B Color Temp 9300K + + + + + + + 25 25 25 25 25 25 25 <V-> or V+> key to change STILL Bass - Treb- 27 Trouble shooting Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Possible interferences of automobiles, motorcycle, trolley bus, neon lamps, etc. [. . . ]