User manual PANASONIC CY-VMR5800N

[. . . ] Installation Hardware. . . Needed for monitor setting. Required Tools You'll need a screwdriver and the following: 12 V DC test Electrical tape Slide-cut bulb pliers E N G L I S H 48 Before Installation Warning Do not install the monitor in a location which obstructs driving, visibility or which is prohibited by applicable laws and regulations. If the monitor is installed in a location which obstructs forward visibility or operation of the air bag or other safety equipment or which interferes with operation of the car, it may cause an accident. Never use bolts or nuts from the car's safety devices for installation. If bolts or nuts from the wheel, brakes or other safety devices are used for installation of the monitor, it may cause an accident. [. . . ] C Display unit/control unit connecting cord 5 Mounting bolt (M5) Attach the mounting springs 3 to the display unit. After fixing power connector @ and display unit/control unit connecting cord C, fix the rear of the unit to the car body by either method (a) or (b) shown at right. : Binding-head screw (M5k6 mm) 2 pieces Recycle the binding-head screws that fixed the transportation brackets for two more positions. < Binding-head screw (M4k3 mm) 4 pieces When using these mounting holes 2 3 4 Side of the display unit ; Flat-head screw (M5k6 mm) 4 pieces After installation, 5 tery terminal. reconnect the negative - bat- 66 CY-VMR5800N CY-VMR5800N 67 E N G L I S H 53 Installation Guide (Continued) Use the supplied spacer = if mounting hole of your car is shaped like below. : Binding-head screw (M5a6 mm) Mounting the Speaker (Supplied) Before mounting the speaker, wipe a drop of water, dust and an oil stain off from the place where the speaker should be mounted to enhance adhesive strength. D Double-faced adhesive tape E N G L I S H 54 Mounting hole of a bracket (in section) Bracket = Spacer : Binding-head screw (M5a6 mm) = Spacer Existing bracket (R) > Double-faced adhesive tape > Double-faced adhesive tape Existing bracket (L) (Bracket originally attached to the car. The exterior design differs from that of the actual product. ) Mounting the Control Unit Mounting Example Before mounting the unit, wipe a drop of water, dust and an oil stain off from the place where the unit should be mounted to enhance velcro strength. on the carpet (underneath the passenger seat, etc. ) and mount the control unit on it. Note: Some carpet materials may not be suitable for this mounting method. In this case, please contact your nearest Panasonic Servicenter for installation. Side brake (parking brake) connection lead (Blue/yellow stripe) SIDE BRAKE CY-VMR5800N Control unit (front) RCA cord (optional) Brake light Battery Video (Yellow) B Clip connector When the side brake (parking brake) lever is engaged, the unit is grounded by the chassis. Check the reverse lamp. Car chassis Connecting the Reverse Lead In case using an optional rear view camera, the reverse lead must be connected. Connect the reverse lead (violet/white stripe) to the positive (_) lead of the reverse lamp (the lamp with a clear lens that lights when the transmission gear is shifted into the reverse position). Notes: Connect the reverse lead after cutting the terminal at the end. Use a reverse extension cord A if needed. 1 Attach a clip connector B to the end of the side brake (parking brake) connection lead. Side brake (parking brake) connection lead (Blue/yellow stripe) 2 The clip connector B is connected to the power source side lead of the side brake (parking brake) lever. Take it out of the back of the tail lamp mount. Reverse lamp Clip connector Comes up to this point. Power source side lead Battery Car chassis Reverse lead (Violet/white stripe) P R N D 2 L Transmission gear Cut here. 78 CY-VMR5800N CY-VMR5800N 79 E N G L I S H 65 Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit yourself because it is dangerous to do so. Cautions: Do not use the unit if it malfunctions or is something wrong. Do not use the unit in abnormal condition, for example, without sound, or with smoke or foul smell, can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it. Common (continued) Trouble Cause/Step The volume is adjusted to zero. [. . . ] Dolby Digital This fully discrete format divides the music signals into 5. 1 channels: Front Left (L), Front Right (R), Center (C), Left Surround (LS), Right Surround (RS) and Subwoofer (SW: 0. 1 channel) for recording and playback. (1 to 5. 1 channels) Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. Dolby Pro Logic This format records signals from four channels [Front Left (L), Front Right (R), Center (C), and Monaural Surround (S)] in two channels, decodes those channels through a Dolby Pro Logic decoder, and then outputs the resulting signals in four channels. [. . . ]