User manual PANASONIC KXHNS103

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PANASONIC KXHNS103. We hope that this PANASONIC KXHNS103 user guide will be useful to you.


PANASONIC KXHNS103 : Download the complete user guide (974 Ko)

Manual abstract: user guide PANASONIC KXHNS103

Detailed instructions for use are in the User's Guide.

[. . . ] A B C *1 *2 *3 A Accessory item/Part number Battery*1 Wall mounting adaptors*2 Wall mounting screws (25 mm (1 inch))*3/XTB4+25AVW Quantity 1 2 3 When replacing the battery, see “Power source” of “Specifications”, page 19 for battery information. 1 adaptor for the main unit: PNHR2107Z 1 adaptor for the probe unit: PNHR2108Z 2 screws for the main unit and 1 screw for the probe unit B C Other information R Design and specifications are subject to change without notice. R The illustrations in these instructions may vary slightly from the actual product. R Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. [. . . ] F G Main unit Main unit cover M N Used to confirm the status of the sensor or register the sensor to the hub. LED indicator Cable Probe unit Probes Setup overview 1 Initial setup Make sure you can access the system using your mobile device. Confirm the usage area Read the information in this document to confirm that the desired installation area is suitable to proper operation. 2 3 4 LED indicator N and check the You can press M LED indicator to confirm the sensor’s status. After confirming the sensor’s status, we recommend turning the LED indicator 5 8 For assistance, please visit www. Registering the sensor This procedure is not required for devices that were included as part of a bundle. You can register each device by using the registration buttons or the [Home Network] app. Using registration buttons 1 Hub: 2 OTHER Press and hold M DEVICEN until the LED indicator blinks in green. Sensor: Remove the main unit cover and press and hold M N until the LED indicator blinks in green (page 8). Note: R To cancel without registering the N on the hub and sensor, press M on the sensor again. Using the app When you register the sensor by using the [Home Network] app, you can assign a name to your devices and For assistance, please visit www. Pdf 12 2015/02/03 20:01:37 Setup Securing with the wall mounting adaptors 1 Use screws to attach the wall mounting adaptors to the wall. N Main unit 1 Screws 2 75 mm (2 15/16 inches) n Probe unit 1 Screw 1 2 1 1 Note: R To install the probe unit on a floor, see page 16. In this case, you will not use the probe unit’s wall mounting adaptor. Pdf 13 2015/02/03 20:01:37 Setup 2 Remove the backing from the double-sided tape, insert the main unit and the probe unit into the wall mounting adaptors, and then press firmly on each unit to ensure solid adhesion to the installation surface. Pdf 14 2015/02/03 20:01:37 Setup Securing with double-sided tape only Note: R Make sure any surfaces that will make contact with the double-sided tape are clean and dry before applying the tape. Android™ devices Tap or press your mobile device’s menu button in the app’s home screen. Note: R Microsoft® Windows® Internet Explorer® 8 and earlier versions are not supported. R You can also access the User’s Guide at the web page listed below. Features available when using the [Home Network] app Some of the sensor’s features that are available when using the [Home Network] app are listed below. €“ Alarm system You can use the app to arm and disarm the alarm system, confirm the current status of the sensor, and view a log of previous events. €“ Sensor integration You can configure the sensor to trigger other system events, such as camera recording, turning on an electric device (such as a lamp), etc. [. . . ] The decision to repair, replace or refund will be made by the warrantor. Parts Labor Home Network System Products One (1) Year One (1) Year microSD card (Included model only) 90 days N/A During the “Labor” Limited Warranty period there will be no charge for labor. During the “Parts” Limited Warranty period, there will be no charge for parts. You must mail-in your product prepaid during the Limited Warranty period. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PANASONIC KXHNS103




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PANASONIC KXHNS103 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.