User manual PANASONIC KX-TG6422E

[. . . ] (found on the bottom of the base unit) Date of purchase Name and address of dealer Note: L In the event of problems, you should contact your equipment supplier in the first instance. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www. doc. panasonic. de Contact: Panasonic Services Europe a Division of Panasonic Marketing Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, Germany Trademarks: L Eatoni and LetterWise are trademarks of Eatoni Ergonomics, Inc. 2 TCD230-240FX(e). book Page 3 Wednesday, June 8, 2005 7:15 PM Feature highlights Feature highlights Phonebooks This unit provides the handset phonebook (200 names and phone numbers; page 20) and the shared phonebook (20 names and phone numbers: KX-TCD240 only; page 22). These phonebooks allow you to make calls without having to dial manually. [. . . ] 7 Press {ih}. Note: L The following items will be deleted or reset to their default settings: ­ Settings listed on page 26 ­ Redial list ­ Voice enhancer ­ Category names ­ Category ringtones L The following items will be retained: ­ Handset phonebook entries (Category names and ringtones will be reset to their default settings. ) ­ Date and time 3 Select "Other Options", then press {>}. 4 Select "LetterWise", then press {>}. Turning keytones on/off Keytones are tones heard when keys are pressed. 2 Select "Handset Setup", then press {>}. 3 Select "Other Options", then press {>}. 4 Select "Keytones", then press {>}. 6 Press {ih}. Note: L If keytones are turned off, error tones will not sound when you enter the wrong PIN or when memory is full. Resetting the handset to its default settings 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Other Options", then press {>}. 31 TCD230-240FX(e). book Page 32 Wednesday, June 8, 2005 7:15 PM Base Unit Settings Guide to base unit settings For your reference, a chart of all items which can be customised for the base unit is printed below. L When customising the base unit, the current item or setting is indicated by >. Base unit settings menu Ringer Setup Sub-menu Night Mode Sub-menu 2 Start/End On/Off Ring Delay Call Options Dial Mode Recall Pause Length Emergency No. Call Restrict Call Bar Other Options Base Unit PIN Repeater Mode Reset Base Off 0000 Off -- Default setting 23:00/06:00 Off 60 sec. -- -- Page page 33 page 33 page 33 page 13 page 34 page 34 page 34 page 34 page 35 page 35 page 55 page 36 Note: L Up to 3 menu items can be displayed at a time. To select a menu item not shown on the current page, scroll up or down by pressing the navigator key, {e} or {v}, respectively. L To change the base unit ringer volume and the base unit ringtone, see page 19. 32 TCD230-240FX(e). book Page 33 Wednesday, June 8, 2005 7:15 PM Base Unit Settings Ringer setup Night mode Night mode allows you to select a block of time during which the base unit will not ring for outside calls. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 35). 4 Select "Call Options", then press {>}. 5 Select "Call Restrict", then press {>}. L The base unit extension number "0" and the extension numbers of all registered handsets are displayed. 4 Select "Call Options", then press {>}. 5 Select "Call Bar", then press {>}. 7 Press {ih}. 6 Select the extensions which will be restricted by pressing the desired number. L Flashing numbers indicate call restriction is turned on for the corresponding extension. L To turn call restriction off for an extension, press the dial key corresponding to its extension number. The number will stop flashing. Other options Changing the base unit PIN (Personal Identification Number) For security, the base unit PIN must be entered when changing certain settings. If you forget your PIN, consult your nearest Panasonic service centre. 7 Press {j/OK}. L If the memory location already contains a restricted number, the number is displayed. 9 Enter the phone number or area code to be restricted (8 digits max. ), then press {j/OK}. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it. 10 Press {ih}. Turning call bar on/off This feature prohibits making outside calls with the base unit. When call bar is turned on, only intercom calls and calls to emergency numbers (page 34) can be made. [. . . ] I fully charged the batteries, but L Clean the charge contact and charge again (page 7 still flashes. We recommend connecting a filter (contact your DSL service provider) to the telephone line between the base unit and the telephone line jack. While viewing caller information, L Do not pause for over 1 minute while searching. If you have multiple handsets, you can confirm which handset is handset 1 by pressing {x} and {1} on the base unit. [. . . ]