User manual PANASONIC KX-TG6442

[. . . ] For your future reference Attach or keep original receipt to assist with any repair under warranty. (found on the bottom of the base unit) Date of purchase Name and address of dealer To use this product in Czech or Slovakia, change the unit's region setting (page 41) to match your country. Note: L In the event of problems, you should contact your equipment supplier in the first instance. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. [. . . ] i # i {ih} Setting the ring delay for night mode This setting allows the base unit to ring during night mode if the caller waits long enough. If you select "No Ringing", the base unit will not ring during night mode. Night mode Night mode allows you to select a block of time during which the base unit will not ring for outside calls. This feature is useful for times when you do not want to be disturbed, for example, while sleeping. Night mode can be set independently for the handset (page 32) and the base unit. Setting the start and end time for night mode 1 " (centre of joystick) i n i # 2 Enter the base unit PIN (default: "0000"). 3 4 5 6 "Ringer Setup" i # "Night Mode" i # "Ring Delay" i # Select the desired setting. i # i {ih} 1 " (centre of joystick) i n i # 2 Enter the base unit PIN (default: "0000"). Note: L When the answering system answers the call, this feature does not work. 3 4 5 6 "Ringer Setup" i # "Night Mode" i # "Start/End" i # Enter the desired hour and minute you wish to start this feature. wish to end this feature. Call options Changing the recall time Change the recall time, if necessary, depending on the requirements of your service provider or PBX. 7 Enter the desired hour and minute you 8 # i {ih} Turning night mode on 1 " (centre of joystick) i n i # 2 Enter the base unit PIN (default: "0000"). 1 " (centre of joystick) i n i # 3 "Call Options" i # 4 "Recall" i # 5 Select the desired setting. i # i {ih} 38 TCD820FX(e-e). book Page 39 Tuesday, September 13, 2005 9:10 AM n Base Unit Settings Setting pause length Change the pause length, if necessary, depending on the requirements of your service provider or PBX. Storing carrier codes for ARS (Turning ARS on) Store the carrier codes of the telephone carriers you use. You can store up to 5 carrier codes. 1 " (centre of joystick) i n i # 2 Enter the base unit PIN (default: "0000"). 1 " (centre of joystick) i n i # 2 Enter the base unit PIN (default: "0000"). 3 "Call Options" i # 4 "Pause Length" i # 5 Select the desired setting. i # i {ih} ARS (Automatic Route Selection) (For Czech and Slovakia only) Different telephone carriers charge different rates for call to different areas. See page 69 if you have difficulty using the features in this section. Example: Handset 1 is sending its data to handset 2 (receiver) Pictures larger than about 50 KB cannot be displayed. L Disconnect the USB cable from the handset when you copy data via infrared interface. L You cannot send or receive data via infrared interface when the battery strength is low. L Only characters shown in the character entry tables (page 61) can be used for phonebook entry names or file names of pictures or melodies. Note: L Certain GSM phones are not compatible with this feature. Infrared port Copying phonebook entries Only names and phone numbers can be copied via infrared interface. 1 Handset 1 and Handset 2 (receiver): " (centre of joystick) i o i # 2 Handset 1: "Send" i # Handset 2 (receiver): "Receive" i # 3 Handset 1: "Phonebook" i # Caution: L This device contains a low power level Class 1 laser product (Infrared LED), which will not normally harm the eyes. Though invisible to the eye, do not point the infrared beam at anyone's eye. Important: L Place the devices about 20 cm from each other, with their infrared ports pointing at each other. L Pictures larger than 176 (height) x 144 (width) pixels cannot be displayed. 4 Handset 1: "1 Entry" i # L To send all entries, select "All Entries". i @ Handset 2 (receiver): c L When receiving more than one entry, "Incoming data. Press # to save all entries. 6 To copy another entry: Handset 1: Repeat step 5. 42 TCD820FX(e-e). book Page 43 Tuesday, September 13, 2005 9:10 AM o Infrared Handset 2 (receiver): Select "Receive", press #, then repeat step 5. [. . . ] Phonebook pictures and pictures smaller than 64 x 68 cannot be reduced. L You erased the picture or ringtone that you set for wallpaper or user ringtone (handset ringtone, memo alarm, or category ringtone). L Only characters shown in the character entry tables (page 61) can be displayed. L Only the first 16 characters of a name and the first 24 digits of a phone number can be received. [. . . ]