User manual PANASONIC NV-FJ615B

[. . . ] ­ The VCR is suddenly brought from cool surroundings, such as an air-conditioned room or car, to a place which is hot and humid. Note: ­ In any of the above-mentioned conditions, do not operate the VCR for at least 1 hour. This VCR is not equipped with a dew sensor. Important Your attention is drawn to the fact that the recording of pre-recorded tapes or discs or other published or broadcast material may infringe copyright laws. Warning To reduce the risk of fire or shock hazard, do not expose this equipment to rain or moisture. [. . . ] Example: Programming the timer recording of a TV programme broadcast on programme position 2 (ZDF) from 20:00 to 21:30 on 27 October. PROG. / CHECK Pos Start Stop VPS Press the [PROG. /CHECK] Name DATE ON OFF 1 PDC 1. ­ Alternatively, you can press the [MENU] button and then select [Timer recording]. jjjjj jjjjj jjjjj jjjjj jjjjj jjjjj jjjjj jjjjj jj/jj jj/jj jj/jj jj/jj jj jj jj jj jj jj jj jj jj:jj jj:jj jj:jj jj:jj jj jj jj jj jj jj jj jj jj:jj jj:jj jj:jj jj:jj jj jj jj jj jj jj jj jj jj jj jj jj jj jj jj jj jjj jjj jjj jjj jjj jjj jjj jjj Timer recording Panasonic VCR 1/2 Press the [SV/V +] button to display the menu for entering the ShowView number on the TV. ShowView 721114 Panasonic VCR Press the [Numeric] buttons to enter the ShowView number. ­ If you have entered a wrong digit, press the [Cursor] button 2 and then enter the correct digit. OK SP/LP/EP Press the [Channel] button to select the programme position of the desired TV station. ­ As an alternative method, after pressing the [Channel] button, you can use the [Cursor] buttons 3421. Press the [DATE] button to set the date on which the TV programme will be broadcast. Press the [OK] button to display the programmed content. (For NV-FJ620 Series, NV-FJ621 Series and NV-FJ616 Series) ­ Regarding the [A] indication, refer to page 13. ­ To change timer recording programmings, use the [Cursor] buttons 3421, the [Channel], [DATE], [ON] or [OFF] button. Press the [TIMER] button to switch the VCR over to the timer recording standby mode. (See page 13. ) r DATE s r ON s Press the [ON] button to set the starting time. ­ When it is kept pressed, the indication changes in 30-minute intervals. / CHECK Press the [PROG. /CHECK] button to display the timer recording programmings on the TV screen. ­ When the VCR is in the timer recording standby mode for a VPS/PDC recording, the On Screen Display may be distorted. Press the [Cursor] buttons 34 to select the programming that you want to change or cancel. To change or cancel timer recording programmings, use the [Cursor] buttons 3421, the [Channel], [DATE], [ON], [OFF] or [CANCEL] button. 13 Search Functions Programme List Search ­ Each timer recording programming on the tape must be at least 15 minutes long. (25 minutes in the EP mode) SEARCH Panasonic VCR Date 27/10 28/10 Start 17:46 15:00 Connecting a Decoder (For NV-FJ620 Series, NV-FJ621 Series and NV-FJ616 Series) Decoder here refers to the device used to decode scrambled broadcasts (Pay TV). Press the [SEARCH] button to display the Programme List menu. Programme List Pos Name 1. ARD Press the [Cursor] buttons 34 to select the programme that you want to locate and play back. SEARCH Press the [SEARCH] button to start the search for the beginning of the selected programme. ­ After the desired recorded programme has been found, playback starts automatically. ­ If, after playback has started, you want to search for the beginning of the same or another programme, press the [SEARCH] button. Playback stops, and the Programme List menu appears. 1 2 3 1 3 2 Decoder (not supplied) 21-pin Scart socket 21-pin Scart cable (not supplied) To Cancel the Programme List Search EXIT Press the [EXIT] button. Notes: ­ If you take out the cassette after a timer recording has finished, pressing the [SEARCH] button activates the IntroJet Scan. ­ If you programme linked timer recordings, Programme List Search function does not work. Connect a 21-pin Scart cable (not supplied) to the AV2 21-pin Scart socket on the VCR and to the 21-pin Scart socket on the decoder. [. . . ] [Download cannot be performed. ] ­ The VCR is not connected to a TV equipped with the Q Link (or a similar) function via a fully-wired 21-pin Scart cable. Be sure to use a fully wired 21-pin Scart cable to connect the VCR to a TV with the Q Link (or a similar) function. (For NV-FJ620 Series, NV-FJ621 Series and NV-FJ616 Series) Playback Does Not Work Properly [The playback picture is distorted or in black and white. Or, horizontal noise bars appear in the picture or horizontal lines move up and down. ] ­ The tracking adjustment is not correct. [. . . ]