User manual PANASONIC PT-AE2000E

[. . . ] Operating Instructions LCD Projector Model No. PT-AE2000E Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0234 ENGLISH Important Safety Notice Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. You should note it in the space provided below and retain this booklet in case service is required. Important Information Model number: Serial number: WARNING: WARNING: PT-AE2000E THIS APPARATUS MUST BE EARTHED. [. . . ] · If you project a copyrighted image enlarged or distorted by using ASPECT function in commercial use in a public place, such as a restaurant or hotel, you might infringe on the copyright of the creator which is protected by copyright law. VIDEO/S-VIDEO/COMPONENT (YPBPR) 4:3 16:9 14:9 JUST ZOOM2 ZOOM1 COMPUTER (RGB) 4:3 16:9 Loading a saved setting You can access saved settings instantly. Select the required setting from MEMORY1 - 16. Undefined setting will not be displayed. NOTE: · If you have not saved any settings, MEMORY1 - 16 will not be displayed. 2. Press ENTER to activate the selected setting. ENGLISH - 23 Basic Operation · If you select an unplugged input method, the guidance will blink on and off several times. · See "Connections" on page 18. Remote control operation Adjusting the signal condition with a waveform You can display the image brightness and contrast level of the input signal with a waveform. See "WAVEFORM MONITOR" on page 32. Monitoring the waveform of brightness and contrast of the whole image. Monitoring the waveform of SINGLE LINE SCAN brightness and contrast in each horizontal line of the image. FULL SCAN COMPUTER (except 1080) HDMI (Expand) 100% Adjust to 100% 100% 50% Adjust to 100% 100% 0% Signal level ENTER ENTER 50% Signal level 50% 0% Optimal dynamic range Monitor position 0% Optimal dynamic range Monitor position Adjust to 0% Adjust to 0% Displaying the waveform 1. Press the WAVEFORM button and display the waveform monitor. Press the WAVEFORM button again to escape from the waveform mode. Adjustment example Project a commercial test signal for picture adjustment on the screen and press the WAVEFORM button. Basic Operation 2. Press ENTER button until the required waveform option is displayed. In FULL SCAN mode, press F G I H to change the waveform position. In SINGLE LINE SCAN mode, press F G to select the required line position. FULL SCAN(Y) FULL SCAN(R) FULL SCAN(G) FULL SCAN(B) SINGLE LINE SCAN(B) SINGLE LINE SCAN(G) SINGLE LINE SCAN(R) SINGLE LINE SCAN(Y) Adjusting with luminance options 1. Press the ENTER button until FULL SCAN(Y)/ SINGLE LINE SCAN(Y) is displayed. Adjust the BRIGHTNESS by pressing I H. Adjust the bottom line of the waveform to 0% (0 or 7. 5 IRE). Adjust the CONTRAST by pressing I H. Adjust the bottom line of the waveform to 100% (100 IRE). Setting range: -64 to +64 FULL SCAN(Y)/SINGLE LINE SCAN(Y) Adjust the bottom line of the BRIGHTNESS waveform to 0% (0 IRE or 7. 5 IRE) Adjust the top line of the waveform CONTRAST to 100% (100 IRE) NOTE: · In SINGLE LINE SCAN mode, the position of the waveform monitor depends on the position of the selected line. · You can display the main menu by pressing the MENU button and adjust the menu items. · The called up menu items displayed position depends on the position of the waveform monitor. · You can activate AUTO ADJUST of the WAVEFORM menu by pressing the DEFAULT button. · The signal which is lower than 0% in the waveform will be displayed as same as 0% on the projected image. · While the waveform is displayed, the image is displayed without the COLOUR MANAGEMENT adjustment. · When adjusting the KEYSTONE of the POSITION menu while the waveform is displayed, xvYCC will be deactivated. 24 - ENGLISH Remote control operation Adjusting with RGB options 1. Adjust the brightness option by pressing I H. Adjust the bottom line of the waveform to 0% (0 IRE or 7. 5 IRE). [. . . ] 13 SHARPNESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SLEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 SPLIT ADJUST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]