User manual PANASONIC PT-D5500E

[. . . ] You should note it in the space provided below and retain this booklet in case service is required. Important Information Model number: PT-DZ8700U/PT-DS8500U/PT-D5500E Serial number: WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. This Projector is designed to operate on 120 V, 60 Hz AC, house current only. Power Supply: CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire may result. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] z If conventional (normal) 4 : 3 pictures which are not wide-screen pictures are displayed on a wide screen, the edges of the pictures may not be visible or they may become distorted. Such pictures should be viewed as with an aspect ratio of 4 : 3 in the original format intended by the creator of the pictures. Note J THROUGH Pictures are displayed without changing the resolution of the input signals. J 16 : 9 When standard signals *4 are input, the pictures are displayed with the aspect ratio converted to 16 : 9. When wide signals are input *5, the pictures are displayed without changing the aspect ratio. J4 : 3 When standard signals *4 are input, the pictures are displayed without changing the aspect ratio. When wide signals are input *5 and [4:3] is selected with [SCREEN FORMAT], the aspect ratio is changed to 4:3. If [4:3] is not selected with [SCREEN FORMAT], the pictures are reduced so that they will be in the 4:3 screen without changing the input aspect ratio. ZOOM This adjusts the size of the projected pictures. 1 ) Press to select [ZOOM]. 2 ) Press <ENTER> button. z The [ZOOM] screen will be displayed. J H FIT The display will use the full width of the screen range selected with [SCREEN FORMAT]. When signals have a vertical aspect ratio that is larger than the screen aspect selected with [SCREEN FORMAT], the pictures will be displayed with their bottom areas cut off. 3 ) Press to select [VERTICAL]/ [HORIZONTAL], and press to adjust. J When [ASPECT] is set to [DEFAULT] J V FIT The display will use the full height of the screen range selected with [SCREEN FORMAT]. INTERNAL J HV FIT The pictures are displayed in the full screen range selected with [SCREEN FORMAT]. If the aspect ratios of the input signals and screen range differ, conversion to the screen aspect set with [SCREEN FORMAT] is performed and then the pictures are displayed. *4 : Standard signals are input signals with an aspect ratio of 4 : 3 or 5 : 4. *5 : Wide-screen signals are input signals with an aspect ratio of 16:10, 16 : 9, 15 : 9 or 15 : 10. Zoom area is the factory default setting of [SCREEN FORMAT] in [SCREEN SETTING]. Enlarges the size of the pictures using the whole of the display area selected with [SCREEN FORMAT]. FULL ENGLISH - 59 Settings 1 ) Press to select [MODE]. z The adjustment value for the PT-D5500E can be changed within a range of 0 to 383 vertically and 0 to 682 horizontally. When correcting the upper blanking of the screen (top) Press to move the blanking zone upward; Press to downward. When correcting the lower blanking of the screen (bottom) 3 ) Press to select [DIGITAL CINEMA REALITY]. z The setting will change as follows each time is pressed. AUTO OFF 25p FIXED : When 576i or 1 080/50i signals are input 30p FIXED : When 480i or 1 080/60i signals are input AUTO OFF 25p FIXED Unforced cinema processing. Forced cinema processing (2 : 2 pulldown) is performed when a 576i or 1 080/50i signal is input. Forced cinema processing (2 : 2 pulldown) is performed when a 480i or 1 080/60i signal is input. 30p FIXED Note When correcting the left hand blanking of the screen (left) Press to move the blanking zone to the right; Press to the left. When correcting the right hand blanking of the screen (right) Press to move the blanking zone to the right; Press to the left. z In [DIGITAL CINEMA REALITY] mode, the image quality will be deteriorated if [30p FIXED] or [25p FIXED] is selected when the signal is not a 2 : 2 pulldown signal. ENGLISH - 63 Settings Performs automatic detection and cinema processing. (factory default) Press to move the blanking zone upward; Press to downward. ADVANCED MENU INPUT RESOLUTION Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. Set the values appropriately for the signal resolution that is being used. EDGE BLENDING The built-in edge blending feature allows multiple projector images to be seamlessly overlapped. 1 ) Press to select [INPUT RESOLUTION]. 2 ) Press <ENTER> button. displayed. 1 ) Press to select [EDGE BLENDING]. 2 ) Press to switch [EDGE BLENDING]. is pressed. z The [INPUT RESOLUTION] screen will be z The setting will change as follows each time 3 ) Press to select [TOTAL DOTS], [DISPLAY DOTS], [TOTAL LINES] or [DISPLAY LINES], and the press to adjust it. z Each item automatically displays a value in OFF ON USER OFF ON When the multi-screens are not going to be used. [. . . ] 24. 0 kg (52. 9 lbs. ) *4 Temperature *5 : 0 °C to 45 °C Humidity : 10 % to 80 % (no condensation) DC 3 V (AA/R6 battery × 2) Approx. 30 m (98'5") (when operated directly in front of signal receptor) 134 g (4. 7 ozs. ) (including batteries) Width : 51 mm (2"), Length : 176 mm (6 15/16"), Height : 28 mm (1 3/32") For high ceiling : ET-PKD310H For low ceiling : ET-PKD310S Ceiling Mount Attachment : ET-PAD310 ET-D75LE6, ET-D75LE1, ET-D75LE2, ET-D75LE3, ET-D75LE4 ET-D75LE5, ET-D75LE8 ET-D75LE10, ET-D75LE20, ET-D75LE30 ET-D75MC1 ET-LAD310 (1 bulb), ET-LAD310W (2 bulbs) ET-ACF310 ET-SFD310 ET-PFD310 -- PT-D5500E Projection lens Lens Motor Cover Replacement Lamp Unit Replacement filter unit Smoke Cut Filter Frame Options z The part numbers of accessories and separately sold components are subject to change without notice. ENGLISH - 125 Appendix *1 : Measurement, measuring conditions and method of notation all comply with ISO21118 international standards. *2 : For details of video signals that can be projected using this projector, refer to "List of compatible signals" (Æpage 122). *3 : If ET-D75LE5 is installed, screen size is 70 inches - 300 inches. [. . . ]