User manual PANASONIC PT-D5500EL

[. . . ] You should note it in the space provided below and retain this booklet in case service is required. Model number: Serial number: WARNING: PT-DZ6710U/PT-D5500EL/PT-DW6300U/PT-D6000U/PT-D5000U TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. This Projector is designed to operate on 120 V, 60 Hz AC, house current only. The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. [. . . ] Attach the lamp unit cover and tighten the "lamp unit cover fixing screw" (1 screw) securely with a Phillips-head screwdriver. Slide the lamp unit cover to the hinge side along the guide and push in to attach securely. Make sure the fan electric power connector of the lamp unit cover is inserted securely to the projector's connector. Handle Lamp unit fixing screws NOTE: ENGLISH - 31 Maintenance · The lamp unit and the lamp unit cover must be attached correctly and securely. Failure to do so, the projector will bot be turned on for the protection circuit. · When the lamp unit is replaced, the duration of usage time will be reset to "0". Replacement Replacing the Auto Cleaning Filter (ACF) Before replacing the ACF Wait until the cooling fan stops and turn off the POWER switch of the projector in proper way. Contact an Authorized Service Center to purchase a replacement ACF (ET-ACF100). The ACF unit to be replaced should be an unused product. When to replace the ACF The ACF unit is consumable product and effects on ventilation. You can check the remaining amount of the ACF unit in REMAINING FILTER of STATUS in PROJECTOR SETUP menu. Replacement procedure 1. Loosen "ACF cover fixing screw" (1 screw) until the screws turn freely and remove the ACF cover. Resetting the REMAINING FILTER 1. Turn on the projector and display the FILTER COUNTER RESET in PROJECTOR SETUP menu. Press the ENTER button. The confirmation screen will be displayed. 3. Display the STATUS in PROJECTOR SETUP menu and confirm the REMAINING FILTER. NOTE: ACF cover fixing screw ACF cover · See FILTER COUNTER RESET and STATUS in PROJECTOR SETUP menu of the functional instructions that is in the provided CD-ROM. 2. Where Plug and Play is unmarked and nothing is written in the format list, difficulties in projecting image may occur even when computer and projector appear to have same resolution. V = VIDEO, S = S-VIDEO, D = DVI, R = RGB, Y = YPBPR SDI is only for the PT-DZ6710U. VESA CVT-RB (Reduced Blanking) compatible. NOTE: · Projecting an interlaced signal may cause flicker in screen. Display dots of each model PT-DZ6710U PT-D5500EL PT-DW6300U PT-D6000U/PT-D5000U 1 920 x 1 200 1 920 x 1 200 1 280 x 800 1 024 x 768 ENGLISH - 35 Appendix Technical Information Specifications Power supply AC 120 V 60 Hz · · · · · · Panel size (diagonal) Aspect ratio DLPTM chip Display method Pixels Motorized zoom Lens Motorized focus · Lamp · · · Luminosity*2 · · · · · · · · · · PT-DZ6710U/PT-D5500EL: 820 W PT-DW6300U/PT-D6000U: 780 W PT-D5000U: 610 W PT-DZ6710U/PT-D5500EL: 8 A PT-DW6300U/PT-D6000U: 7. 2 A PT-D5000U: 5. 5 A PT-DZ6710U/PT-D5500EL: 0. 67 type · · PT-DZ6710U/PT-D5500EL/PT-DW6300U: 16 : 10 PT-D6000U/PT-D5000U: 4:3 PT-DZ6710U/PT-D5500EL: 2 304 000 (1 920 x 1200) PT-DW6300U: 1 024 000 (1 280 x 800) PT-D6000U/PT-D5000U: 786 432 (1 024 x 768) · F 1. 7 - 2. 0, f 25. 6 mm - 33. 8 mm PT-DZ6710U/PT-D5500EL: f = 26. 8 mm - 35. 7 mm PT-DW6300U/PT-D6000U/PT-D5000U: f = 25. 6 mm - 33. 8 mm Lens is optional for the projectors that "L" follows in model number. PT-DW6300U: 0. 65 type PT-D6000U/PT-D5000U: 0. 7 type Power consumption During standby (when fan is stopped): Approx. 8 W*1 Amps 1 unit DLPTM chip, DLPTM type 1. 8 - 2. 4:1 PT-DZ6710U/PT-D5500EL/PT-DW6300U/PT-D6000U: UHM lamp (300 W) x 2 PT-D5000U: UHM lamp (240 W) x 2 PT-DZ6710U/PT-D5500EL/ PT-DW6300U:6 000 lm (ANSI) PT-D6000U: 6 500 lm (ANSI) PT-D5000U: 5 000 lm (ANSI) · Lens is optional for the projectors that "L" follows in model number. Average value of the lens that is provided with the projector. Operating environment VIDEO/S-VIDEO Temperature: 0 °C - 45 °C (32 °F - 113 °F)*3 Humidity: 20% - 80% (no condensation) H: 15. 75 kHz/15. 63 kHz, V: 50 Hz/60 Hz H: 15 - 91 kHz, V: 50 - 85 Hz Panasonic Intelligent Auto Scanning (PIAS) RGB Dot clock frequency · PT-DZ6710U/PT-D5500EL: 162 MHz or less · PT-DW6300U/PT-D6000U/PT-D5000U: 150 MHz or less 480p, 576p, 720/60p, 720/59. 94p, 720/50p, 1 080/60p, 1 080/59. 94p, 1 080/50p, 1 080/60i, 1 080/59. 94i, 1 080/50i, 1 080/24sF, 1 080/23. 98sF, 1 080/30p, 1 080/29. 97p, 1 080/25p, 1 080/24p, 1 080/23. 98p Displayable resolution: VGA - WUXGA (non interlace) Dot clock frequency: 25 - 162 MHz WUXGA signal is applicable with VESA CVT-RB (Reduced Blanking). · · · · · · · · 480i 480p 720/50p 1 035/60i 1 080/60i 1 080/25p 1 080/24sF 1 080/60p H: 15. 73 kHz, V: 59. 94 Hz H: 31. 5 kHz, V: 59. 94 Hz H: 37. 5 kHz, V: 50 Hz H: 33. 75 kHz, V: 60 Hz H: 33. 75 kHz, V: 60 Hz H: 28. 13 kHz, V: 25 Hz H: 27 kHz, V: 48 Hz H: 67. 5 kHz, V: 60 Hz · · · · · · · 576i 576p 720/60p 1 080/50i 1 080/24p 1 080/30p 1 080/50p H: 15. 63 kHz, V: 50 Hz H: 31. 25 kHz, V: 50 Hz H: 45 kHz, V: 60 Hz H: 28. 13 kHz, V: 50 Hz H: 27 kHz, V: 24 Hz H: 33. 75 kHz, V: 30 Hz H: 56. 25 kHz, V: 50 Hz DVI-D Scanning frequency*4 YPBPR HD/SYNC, VD terminals are not compliant with 3 value composite SYNC. Color system 7 (NTSC/NTSC 4. 43/PAL/PAL-M/PAL-N/PAL60/SECAM) 50" - 600" (1 270 mm - 12 700 mm)*5 · · PT-DZ6710U/PT-D5500EL/PT-DW6300U: 16 : 10 PT-D6000U/PT-D5000U: 4:3 Appendix Projection size Screen aspect ratio Installation Contrast ratio FRONT/FLOOR, FRONT/CEILING, REAR/FLOOR, REAR/CEILING (Menu selection method) · · PT-DZ6710U/PT-D5500EL/PT-DW6300U/PT-D6000U: 2 000 : 1 (When CONTRAST MODE in DISPLAY OPTION menu is set to HIGH) PT-D5000U: 1 000 : 1 ENGLISH - 36 Technical Information S-VIDEO IN VIDEO IN 1 set, Mini DIN 4p Y: 1. 0 V [p-p], C: 0. 286 V [p-p], 75 , compatible with S1 signal 1 set, BNC pin jack 1. 0 V [p-p], 75 1 set, BNC x 5 RGB signal 0. 7 V [p-p], 75 RGB 1 IN · G-SYNC: 1. 0 V [p-p], 75 · HD/SYNC: TTL high impedance, automatic positive/negative polarity compatible · VD: TTL high impedance, automatic positive/negative polarity compatible YPBPR signal · Y: 1. 0 V [p-p] Synchronisation signal included · PBPR: 0. 7 V [p-p], 75 1 set of high density, D-sub 15p (female) RGB signal Terminals RGB 2 IN 0. 7 V [p-p], 75 (G-SYNC: 1. 0 V [p-p], 75 ) · HD/SYNC: TTL high impedance, automatic positive/negative polarity compatible · VD: TTL high impedance, automatic positive/negative polarity compatible YPBPR signal · Y: 1. 0 V [p-p] Synchronisation signal included · DVI-D IN SERIAL REMOTE1 REMOTE2 LAN SDI Cabinet Power cord length Dimensions Weight Power supply Operating range Remote control Weight PBPR: 0. 7 V [p-p], 75 1 set, DVI-D 24-pin (Single link), DVI 1. 0 compatible, HDCP compatible 1 set, D-sub 9-pin, RS-232C compatible, computer control use 1 set, M3 pin jack, wired remote control use, multiple connection use 1 set, D-sub 9-pin, external control use 1 set, RJ-45, network connection use, PJLinkTM compatible, 10 Base-T/100Base-TX 1 set, BNC SD-SDI (Y, CB, CR, 4:2:2) · SMPTE259M: 480i, 576i Moulded plastic 3. 0 m (9'10") Width Height Length Approx. 16 kg (35. 3 lbs. )*6 498 mm (19- 19/32") 175 mm (6 - 7/8") 440 mm (17 - 5/16") · SMPTE292M: 720/50p, 720/60p, 1 035/60i, 1 080/50i, 1 080/60i, 1 080/25p, 1 080/24p, 1 080/24sF, 1 080/30p 3 V DC (AA battery x 2) Approx. 30 m (98'5") (when operated directly in front of signal receptor) 120 g (4. 2 ozs. ) (including batteries) Width 51 mm (2') 176 mm (6 - 29/32") 22. 7 mm (-7/8") (not including surface projection parts) Length Height Dimensions Ceiling bracket Projection lens Options Lamp unit ACF unit ET-PKD56H (High ceiling), ET-PKD55S (Low ceiling) ET-DLE150, ET-DLE250, ET-DLE350, ET-DLE450, ET-DLE055 ET-LAD60 (1 bulb), ET-LAD60W (2 bulbs) ET-ACF100 ENGLISH - 37 Appendix *1. Measurement, measuring conditions and method of notation all comply with ISO21118 international standards. [. . . ] Pour effacer l'écran, appuyez sur n'importe quelle touche. ATTENTION: · Si vous continuez à utiliser la lampe au-delà de 2 000*1 heures, elle endommagera le projecteur. Le projecteur sera mis hors tensions après 10 minutes. REMARQUE: · Les durées indiquées, de 1 800*2 et 2 000*1 heures, sont des estimations basé sur certaines conditions et ne représentent en aucun cas des durées garanties. · Pour de plus amples informations sur la lampe, telle que la durée de fonctionnement garantie, voir les instructions fournies avec la lampe. 2 800 heures pour le PT-D5000U. FRANÇAIS - 49 Information Importante Remplacement Information Importante Procédure de remplacement 6. [. . . ]