User manual PANASONIC PT-D5700E

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: This equipment is equipped with a three-pin grounding-type power plug. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. Do not remove 2 WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] · Keystone distortion can be corrected to ±40° of the angle of tilt for the projector against the screen. (The range for the angle of elevation is within ±19° when using a lens with a fixed focal point, and it is within ±34° when using an LE1 lens. ) 60 How to use ADVANCED MENU DIGITAL CINEMA REALITY Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i signal input is applied. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "MENU" button. The MAIN MENU screen will be displayed. Select "ADVANCED MENU" with the buttons. Press "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "DIGITAL CINEMA REALITY" with the buttons. OFF 75 OFF: Unforced cinema processing AUTO: Performs automatic detection and cinema processing. (factory default) 30p FIXED: Forced cinema processing (2:2 pulldown) is performed when a 480i signal is input. 25p FIXED: Forced cinema processing (2:2 pulldown) is performed when a 576i signal is input. Note · In DIGITAL CINEMA REALITY mode, the image quality will be deteriorated if 30p FIXED or 25p FIXED is selected when the signal is not a 2:2 pulldown signal. FORMAT (To input BETACAM with YCbCr 480i) When receiving a picture of 480i with analog component signal YCbCr input, the input level of Cb and Cr can be switched. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "MENU" button. The MAIN MENU screen will be displayed. Select "ADVANCED MENU" with the buttons. Press "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. OFF 75 Select "FORMAT" with the buttons. Switch the signal format with the buttons. · This toggles between SMPTE and BETACAM. <Signal level> Format SMPTE BETACAM Y 700 mV 714 mV Synchronous part :MENU SELECT :CHANGE Cb , Cr ±350 mV ±504 mV 300 mV 286 mV Note · This function is available only when input signals are supplied through the analog RGB input module (ET-MD95RGB). · This function can be switched only when receiving the picture of 480i in the YCbCr mode. It cannot be switched when receiving the picture of signals other than RGB-REALITY mode, RGB mode and 480i. · SMPTE is the factory default. 61 How to use ADVANCED MENU Blanking adjustment Blanking adjustment fine-tunes the images projected by the video deck or other devices when the noise appears on the edges of the screen or if a part of the image lies slightly offscreen. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "ADVANCED MENU" with the buttons. :MENU SELECT ENTER:SUB MENU ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "BLANKING" with the buttons. OFF 75 :MENU SELECT ENTER:SUB MENU BLANKING UPPER LOWER LEFT RIGHT Press the "ENTER" button. 0 0 0 0 The BLANKING adjustment screen will be displayed. Select the desired item for adjustment with the buttons. · When a rear screen or screen with a high gain is used, the joints may appear to be discontinuous depending on the viewing position. How to switch the input impedance (signal level) of the synchronization signal When the ET-MD95RGB input module (sold separately) is mounted, the user can switch the input impedance (signal level) of the synchronization signal with the analog RGB input. Choose 75 when connecting with the equipment whose synchronization output impedance is 75 such as a signal selector, or switch to HI-Z (TTL) when connecting with the equipment whose synchronization output is TTL such as a video card of a PC. MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select "ADVANCED MENU" with the buttons. :MENU SELECT ENTER:SUB MENU 66 ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. OFF 75 Select "SYNC. TERM" with the buttons. Switch the input impedance (signal level) of the synchronization signal with the buttons. · These buttons toggle between 75 and HI-Z (TTL). SYNC. TERM 75 HI-Z (TTL) Signal level Amplitude: 0. 6V[p-p] to 4. 0V[p-p] High level: 2. 0 V or over Low level: 0. 8 V or lower Input impedance 75 1 k :MENU SELECT :CHANGE Note · Switch the input impedance according to the input signal. · The clock phase and image position may become out of balance during this switching operation. Please make readjustment accordingly. Raster position When the whole area where the input picture can be displayed is not used, the picture can be moved to any position inside the display area. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select "ADVANCED MENU" with the buttons. ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "RASTER POSITION" with the buttons. OFF 75 RASTER POSITION V: H: Press the "ENTER" button. 0 0 The RASTER POSITION screen will be displayed. Adjust the position with the , , and buttons. Press the "MENU" button three times. The on-screen indications disappear and the normal screen appears again. (Continued on next page) 67 How to use ADVANCED MENU Raster position (continuing) <When 5:4 pictures are displayed (when SXGA signals are input)> Pressing button will move the image to the right. Pressing button will move the image to the left. <When 16:9 pictures are displayed (when HDTV or 480p pictures are input or 16:9 is selected in the SIZE mode)> Pressing button will move the image upward. Pressing button will move the image downward. Changing the display language MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "LANGUAGE" with the buttons. Press the "ENTER" button. The LANGUAGE screen will be displayed. LANGUAGE ENGLISH DEUTSCH FRANÇAIS ESPAÑOL ITALIANO Select the desired language with the buttons. [. . . ] Si la lampe n'est pas remplacée après 1 300 heures 2 (avec la sortie de la lampe réglée sur "HAUT"), l'alimentation sera automatiquement coupée à 1 500 heures 1, avec passage en mode d'attente. 1 500 heures 1 à partir de l'allumage initial, l'alimentation est automatiquement coupée environ 10 minutes plus tard, avec passage en mode d'attente, même si la lampe est allumée à nouveau. Attention · La lampe est une pièce en option (vendue comme pièce de service). Bloc lampe de rechange, modèle n°: ET-LAD7700 (une ampoule), ET-LAD7700W (deux ampoules) Valeurs nominales: 300 W Bloc lampe longue durée, modèle n°: ET-LAD7700L (une ampoule), ET-LAD7700LW (deux ampoules) Valeurs nominales: 160 W · Des lampes autres que celles spécifiées cidessus ne sont pas utilisables. Utilisez la lampe spécifiée. Indication après 1 300 heures (avec la sortie de la lampe réglée sur "HAUT") 2 Quand la lampe a été utilisée 1 300 heures 2, le témoin de lampe (LAMPE1 ou LAMPE2) s'allume, état d'attente y compris. [. . . ]