User manual PANASONIC PT-D7500E

[. . . ] To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time. This apparatus is equipped with a three prong earthingtype mains plug. [. . . ] Furthermore, if unstable signals are input, the system format can be selected manually. J HDMI terminal input signal z 480p, 576p signals z Other signals Select from Auto, RGB, and YCBCR. Select from Auto, RGB, and YPBPR 1 ) Press to select [SYSTEM SELECTOR]. 4 ) Press <ENTER> button. z Refer to "List of compatible signals" (Æpage 88) for available signals. z Malfunction may occur or other problems could be encountered with some equipment. Note J VIDEO/S-VIDEO terminal input signal To display pictures complying with the sRGB standard sRGB is the international color reproduction standard (IEC61966-2-1) established by IEC (International Electrotechnical Commission). To reproduce colors more faithfully in compliance with the sRGB standard, perform the following setting procedure. Select from AUTO, NTSC, NTSC4. 43, PAL, PAL-M, PAL-N, SECAM, and PAL60. z [AUTO] mode is selected by default. z When the projector is not working properly in [AUTO] mode, change the setting according to each SYSTEM SELECTOR type. z [AUTO] automatically selects from NTSC, NTSC4. 43, PAL, PAL-M, PAL-N, SECAM, and PAL60. Attention Note J RGB1/RGB2 terminal input signal z 480i, 576i, 576p signals z VGA60, 480p signals z Other signals Select from RGB and YCBCR. Select from RGB and YPBPR. z Refer to "List of compatible signals" (Æpage 88) for available signals. Note J DVI-D terminal input signal z 480p, 576p signals 1 ) Set [COLOR MATCHING], [COLOR COLLECTION] adjustment to [OFF]. 6 ) Press <DEFAULT> button on the remote control to restore the factory default. 7 ) Follow the same procedure (steps 5-6) to restore the factory default for [TINT], [COLOR TEMPERATURE] and [GAMMA]. z sRGB is only enable when RGB signals are being input. Select from RGB and YCBCR. z Other signals Select from RGB and YPBPR. z Refer to "List of compatible signals" (Æpage 88) for available signals. *5 : Wide-screen signals are input signals with an aspect ratio of 16:10, 16 : 9, 15 : 9 or 15 : 10. Zoom area is the factory default setting of [SCREEN FORMAT] in [SCREEN SETTING]. Enlarges the size of the pictures using the whole of the display area selected with [SCREEN FORMAT]. FULL ENGLISH - 49 Settings 1 ) Press to select [MODE]. 2 ) Press to switch [MODE]. POSITION menu 3 ) Press to select [INTERLOCKED]. 4 ) Press to switch [INTERLOCKED]. OFF The [VERTICAL] and [HORIZONTAL] settings are used as the vertical and horizontal zoom ratios respectively. This allows the pictures to be zoomed at equal vertical and horizontal ratios. KEYSTONE If the projector is aligned non-perpendicularly to the screen, or if the projection screen has an angled surface, you can correct keystone. ON 1) 2) 3) 4) Press to select [KEYSTONE]. Press to adjust. J KEYSTONE z When [ASPECT] is set to [THROUGH], [ZOOM] will not appear. z When other than [DEFAULT] is selected for [ASPECT], the [MODE] selection setting will not appear. Note CLOCK PHASE Clock phase adjustment achieves the best image when the screen flickers or halos are observed around contours. J SUB KEYSTONE 1 ) Press to select [CLOCK PHASE]. 2 ) Press or <ENTER> button. z The [CLOCK PHASE] individual adjustment J LINEARITY screen will be displayed. 3 ) Press to adjust the level. Note z The value changes from 0 to 63. Adjust so that the amount of interference is at a minimum. z The CLOCK PHASE may not be adjusted, depending on the signal. z No optimal value may be obtained if the output of the PC to which the signal input is applied is unstable. z No optimal value may be obtained if the total number of dots is not correct. [. . . ] A signal of a different resolution than the above data is converted to the number of display dots and then displayed. z The "i" appearing after the resolution indicates an interlaced signal. z Flicker (line flicker) may be caused in images if interlace is connected. Note ENGLISH - 89 Appendix Specifications Model No. Power supply Power consumption Amps Panel size DLP chip Display system Number of pixels Lens Projection lamp Optical output *1 2 304 000 pixels (1 920 × 1 200 dots) 17. 0 mm (0. 67 inch) (aspect ratio 16 : 10) PT-D7500E PT-DW530E AC100 V - 240 V 415 W When [STANDBY MODE] is [ECO] : Approx. [. . . ]