User manual PANASONIC PT-DW5100E

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: This equipment is equipped with a three-pin grounding-type power plug. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. Do not remove 2 WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] However, the greater the correction amount, the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as possible. · The picture size will also change when correction of keystone distortion is carried out. LINEARITY : After you are finished with keystone adjustment, adjust vertical linearity with the or button. Linearity is not adjustable if no correction was made to keystone distortion. 31 How to use ADVANCED MENU ADVANCED MENU DIGITAL CINEMA REALITY BLANKING INPUT RESOLUTION CLAMP POS. 1 RASTER POSITION XGA MODE XGA SXGA MODE SXGA SELSCT RETRN ENTER INPUT RESOLUTION Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. "TOTAL DOTS", "DISPLAY DOTS", "TOTAL LINES" and "DISPLAY LINES" Each item automatically displays a value in response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value. Note · The abovementioned vertical stripes will not appear on the screen when all white signals are input. · The picture may be distorted during the adjusting operation, but this is not a fault. · The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. · Automatic adjustment is not available if signals having a dot clock frequency of more than 108 MHz are supplied. DIGITAL CINEMA REALITY (Only for input of S-Video/ Video/ YPBPR [480i, 576i] signals. ) Set at ON when you need to faithfully capture images shot at 24 frames per second as in movies. When one of the above settings is selected, it will take effect after ENTER is pressed. Note · If, in the "SINGLE", "LAMP1" or "LAMP2" mode, one lamp remains off or the currently active lamp exceeds 1 500 hours of cumulative operating time (when "HIGH" is selected as the lamp power setting), the other lamp will light. If, in the "DUAL" mode, one lamp remains off or the currently active lamp exceeds 1 500 hours of cumulative operating time (when "HIGH" is selected as the lamp power setting), the other lamp alone will light. However, if both lamps remain off or the 1 500 hours of cumulative operating time are exceeded, the projector will enter the standby mode. · If only one lamp is installed in the projector, set lamp mode to either "LAMP1" or "LAMP2". If the corresponding lamp is not installed, the other lamp will turn on. Green Current setting Cyan Now changing from one status to another Red Lamp that has failed to light White Any other status · If the projector is repeatedly used for short periods of time, the lamps will need to be replaced more frequently. This time period is 4 000 hours when long life lamp units (page 43) are used. NORMAL HORIZ. DISABLE RETRN ID The projector has an ID number setting function that helps the user to control two or more projectors either simultaneously or separately with a single remote control. Note · The ID number can be set to "ALL", or selected from "1" to "64". · If the projectors are given ID numbers, their remote controls must be assigned the same ID numbers, respectively. [. . . ] Faites attention que votre main ne glisse pas en utilisant le tournevis. Attention · La lampe est une pièce en option. Contactez le revendeur. Bloc de lampe de rechange, modèle n°: ET-LAD55 (une ampoule), ET-LAD55W (deux ampoules) Valeurs nominales: 300 W Bloc de lampe longue durée, modèle n°: ET-LAD55L (une ampoule), ET-LAD55LW (deux ampoules) Valeurs nominales : 160 W · Des lampes autres que celles spécifiées ci-dessus ne sont pas utilisables. Utilisez la lampe spécifiée. Période de remplacement de la lampe La lampe utilisée comme source lumineuse dans le projecteur a une vie de service de 1 500 heures 1 (quand la sortie de la lampe est FORTE et la sélection de lampe DOUBLE). Il peut arriver que la lampe soit épuisée (ne s'allume pas) à 1 500 heures 1 selon les caractéristiques des lampes individuelles et les conditions de travail (la vie de service des lampes peut être réduite par le nombre d'allumages et les intervalles entre les allumages). [. . . ]