User manual PANASONIC PT-L6510E

[. . . ] Power Supply: This LCD Projector is designed to operate on 100 V ­ 240 V, 50 Hz/60 Hz AC, house current only. CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire may result. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] (Refer to page 31. ) NR (Noise Reduction) (S-VIDEO/VIDEO/YPBPR only) NR ON [ OFF If noise occurs from the projector because of a poor input signal, set NR to "ON". To turn off the NR (Noise 39 Advanced Operation OSD BACK COLOR Basic Operation Use the F and G buttons to select an item, then press the I or H buttons to change the setting. Reduction) feature, set it to "OFF". 4:3 H-POS (4:3 aspect mode only) 4:3 H-POS CENTER [ elevations (above 1 400 m), set FAN CONTROL to "HIGH". RIGHT [ LAMP POWER LAMP POWER HIGH [ LEFT This sets the horizontal positioning of the projected image when the 4:3 aspect ratio is selected. (Refer to page 31. ) LOW FRONT/REAR FRONT/REAR FRONT [ REAR This setting should be changed in accordance with the projector setting-up method. Set to "FRONT" when using a normal reflective screen with the projector positioned in front of the screen, and set to "REAR" when using a translucent screen with the projector positioned behind the screen. This setting changes the lamp brightness. When set to "LOW", the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. The LOW position is recommended for narrow rooms where a high picture luminance is not essential or for watching movies. LAMP RUNTIME This setting displays the usage time for the lamp unit which is currently being used. NOTE: B The lamp's operating life varies depending on the usage conditions (such as the LAMP POWER setting and the number of times the power is turned on and off). DESK/CEILING DESK/CEILING DESK [ CEILING This setting should be changed in accordance with the projector setting-up method. Set to "DESK" when setting up the projector on a desk or similar, and set to "CEILING" when suspending the projector from the ceiling using the ceiling bracket which is sold separately. FAN CONTROL FAN CONTROL NORMAL [ HIGH If using of this projector at high 40 SD memory card What is the SD memory card (option)? The SD memory card is a semiconductor memory which at 24 mm x 32 mm x 2. 1 mm is about the size of a postage stamp. It is a next-generation recording medium which can be used instead of conventional storage devices such as MDs (mini discs), CDs (compact discs) and cassette tapes. In addition, it allows data to be repeatedly recorded, played and erased. The projector can be used to play computer image files, video images (still pictures) and moving pictures using the SD memory card. Record: Digital camera Computer Still image data Moving image data Play back: Still image data Moving image data 16MB Data that can be played back Still image data B DCF compliant still image data (See page 64 for details on DCF compliance. ) Moving image data B MPEG4 movie data (audio: G. 726 compliant) However, only files in ASF format can be played back. Note when using SD memory cards Do not turn off the projector's power or remove an SD memory card from the projector while the SD memory card is in use (while the access indicator is flashing). When "USER" is selected, use the I and H buttons to select the user settings, and then press the ENTER button to start user playback. <Button functions during slide playback> B Pause/cancel automatic playback . . . . . . . ENTER button The following buttons can be used while manual playback or automatic playback is paused. H button B Play back previous image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I button B Rotate images . . . . . . . . . . . . . . . . . . . SD MENU button PICTURE SLIDE SHOW VIDEO SELECT ITEM SETTING ALL FILE FOLDER USER 100 SETTING (page 46) This lets you set whether the slide playback is to be automatically continuous (automatic playback) or whether it can be switched manually (manual playback), and also lets you edit the user settings for "USER". 45 Advanced Operation The still image that will be the first image to be played back for the selected item will be displayed. SETTING SETTING1 AUTO MODE AUTO MODE The still images are played back automatically in order according to the following setting. SETTING2 MANUAL MODE USER SET NEW REPEAT INTERVAL 1 1 USER SET If adding settings for a new user, use the I and H buttons to select "NEW" and then press the ENTER button. If you would like to change the settings for an existing user, use the I and H buttons to select the user setting file (0 9) that you would like to change, and then press the ENTER button. User setting edit screen (A) "REPEAT" ENTER button Use the I and H buttons to select how many times automatic playback is to be repeated. "INTERVAL" Use the I and H buttons to select the time interval (seconds) between playback of each still image. MANUAL MODE During slide playback, press the I button to play back the next still image, and press the H button to play back the previous still image. NOTE: B When editing the user settings, slide playback settings that have not been created using this projector cannot be edited. (B) , 1, 0 , (C) 100-0001 (D) 1/11 (E) (A)Still images set by user (this row is blank for new users) (B)Still images that are available for setting by the user (C)Playback time and rotation angle for selected still image (D)File name of selected still image (E)Number of selected still image/Total number of still images See the next page for details on how to edit user settings. 46 Editing user settings You can use the user setting edit screen that is displayed when you select "SETTING" during slide playback on the previous page to add, move and delete still images from the list of images for slide playback and also to change playback settings. % Use the F, G, I and H buttons to move the cursor (|) to the place where the image is to be added or moved, and then press the ENTER button. Adding and moving images You can select still images that are saved on the SD memory card and add them to the user settings, and also change the order of the still images that have been selected in the user settings. # Use the F, G, I and H buttons to select the still images to be added or moved, and then press the ENTER button. 1, 0 , 100-0001 1/11 Repeat the procedure from step # to add or move additional images. 1, 0 , 100-0001 1/11 B When moving images, only images that have already been added to the user settings can be moved. [. . . ] B La lampe usagée qu'on a retirée risque d'éclater si on la jette sans prendre de précautions. Jeter la lampe de la même manière qu'une lampe fluorescente. REMARQUE: B Le projecteur n'est pas fourni avec un bloc de lampe de rechange. Demander les détails au revendeur. Numéro de produit du bloc de lampe: ET-LAE100 ATTENTION: B Ne pas utiliser un bloc de lampe avec un numéro de pièce autre que celui indiqué ci-dessus. 73 Others Affichage à l'écran Témoin d'alarme de l'indicateur de la lampe Affiché pendant 30 secondes. [. . . ]