User manual PANASONIC PT-L735NTE

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to computers or peripheral devices. [. . . ] If you would like the colors in sRGBcompatible pictures to be reproduced more faithfully, make the following settings. # Press the F or G button to select "PICTURE MODE", and then press the I or H button to select "NATURAL". % Press the F or G button to select "COLOR TEMP. ", and then press the I or H button to select "STANDARD". NOTE: B sRGB is only enabled when RGB signals are being input (when "LAMP POWER" is set to "HIGH"). 36-ENGLISH ENGLISH-37 Adjustments and settings Projecting sRGB-compatible pictures Adjusting the position When an RGB signal is being input, press the AUTO SETUP button first to initiate automatic positioning. If the optimum setting is not obtained when "AUTO SETUP" is carried out, adjust by the following procedure. Press the F or G button on the projector or remote control unit to select an item, and then press the I or H button to change the setting. For items with bar scales, press the ENTER button or the I or H button to display the adjustment screen, and then press the I or H button to make the adjustment. When an RGB/YPBPR signal is being input POSITION Moves the picture position. Press the F or G button to move the picture vertically. ASPECT (S-VIDEO/VIDEO/525i, 525p, 625i and 625p YPBPR signals only) ASPECT AUTO [ 4:3 [ S4:3 The size of the input signal is compressed to 75% and projected. (This is useful for projecting a picture with a 4:3 aspect ratio onto a 16:9 screen. ) 16:9 [ POSITION H V 64 32 S4:3 AUTO (S-VIDEO only) When an S1 video signal is being input, the aspect ratio is changed automatically to project a 16:9 picture. 16:9 The picture is compressed to a ratio of 16:9 and projected. DOT CLOCK (RGB only) Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. RGB or YPBPR is selected automatically depending on the synchronising signal status. When HDTV, 525p, 525i, 625p, 625i, 750p, and some VGA480 signals are being input, select "RGB" or "YPBPR" in accordance with the input signal. FRONT/REAR FRONT/REAR FRONT [ REAR This setting should be changed in accordance with the projector setting-up method. (Refer to page 17. ) FRONT When the projector is placed in front of a screen. REAR When using a translucent screen. LOW This setting changes the lamp brightness. When set to "LOW", the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. If using the projector in small rooms where high luminance is not required, it is recommended that you set the "LAMP POWER" to "LOW". 42-ENGLISH ENGLISH-43 Adjustments and settings OPTION2 BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH LAMP RUNTIME 100H FUNC 1 INDEX CONTROL KEY ON AUTO POW. OFF DISABLE POWER MEMORY ON SELECT ADJ RETRN SXGA+ This setting is only for an SXGA signal. SXGA+ When the edges of the projected image are not visible, select this item. CEILING This setting should be changed in accordance with the projector setting-up method. (Refer to page 17. ) DESK When the projector is placed on a desk or similar. CEILING When the projector is suspended from a ceiling using the ceiling bracket (sold separately). FAN CONTROL FAN CONTROL STANDARD [ BACK COLOR HIGH Set "FAN CONTROL" to "HIGH", when using this projector at high elevations (above 1 400 m) only. Setting up the security function LAMP RUNTIME This setting displays the usage time for the lamp unit which is currently being used. When replacing the lamp unit, follow the instructions on page 51, and reset "LAMP RUNTIME" to "0". NOTE: B The lamp's operating life varies depending on the usage conditions (such as the "LAMP POWER" setting and the number of times the power is turned on and off). CONTROL KEY CONTROL KEY ON [ This projector is equipped with a security function. [. . . ] Il est recommandé de toujours avoir un bloc de lampe de rechange prêt à l'emploi. La lampe s'éteindra automatiquement après environ 10 minutes lorsque la limite de 2 000 heures d'utilisation est atteinte, car le risque d'explosion de la lampe devient beaucoup plus grand passé cette limite. REMARQUE: B Les heures d'utilisation expliquées ci-dessus concernent l'utilisation lorsque le réglage "FORTE" a été sélectionné pour "PUIS. LAMPE" dans le menu "OPTION2". Si le réglage "FAIBLE" est sélectionné, la luminosité de la lampe sera moindre et la durée de vie de la lampe sera allongée. [. . . ]