User manual PANASONIC PT-L780E

[. . . ] If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. Do not remove IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Power Supply: This LCD Projector is designed to operate on 100 V ­ 240 V, 50 Hz/60 Hz AC, house current only. CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 10 A. [. . . ] (pages 44 and 45) NOTE: B sRGB is only enabled when RGB signals are being input . 32 V: 16 0 V: 0 TOP LEFT AUTO OFF ON SELECT:[^][@] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] When a YPBPR signal is being input. POSITION POSITION KEYSTONE OSD POSITION ASPECT RESIZING AUTO SETUP STANDARD H: H: 32 V: 32 0 V: 0 TOP LEFT 4:3 OFF ON H: 32 16 H: 128 V: 32 SELECT:[^][@] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] 0 V: TOP LEFT OFF ON OFF ON 0 When the NETWORK/SD CARD is selected (PT-L780NTU only) POSITION KEYSTONE OSD POSITION AUTO SETUP STANDARD H: SELECT:[^][@] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] 0 V: TOP LEFT 0 "POSITION", "DOT CLOCK" and "CLOCK PHASE" are not displayed when a DVI signal is being input. SELECT:[^][@] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] 38 39 Basic Operation POSITION POSITION H: V: 128 32 Moves the picture position. Press the F or G buttons to move the picture vertically. when using the standard lens. However the horizontal distortion or adjustment of the tilted screen needs to be corrected manually by following any of the procedures below. KEYSTONE H: V: 0 0 DOT CLOCK (RGB only) Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, use the I and H buttons to adjust so that any such noise is minimised. Picture condition Operation Press the G button. [ CLOCK PHASE (RGB only) Adjust the DOT CLOCK setting first before carrying out this adjustment. Use the I and H buttons to adjust so that the noise level is least noticeable. NOTE: B If signals with a dot clock frequency of 140 MHz or higher are being input, interference may not be completely eliminated when the DOT CLOCK and CLOCK PHASE adjustments are carried out. Press the I button. When a squeezed signal is being input. NOTE: B If you press the AUTO SETUP button after correcting the keystone distortion manually, the automatic keystone correction function will operate and the corrected picture will return to its previous incorrect condition. In addition, if you change the input signal and press the AUTO SETUP button, the keystone correction may be cancelled depending on the type of signal and the angle of tilt of the projector. To prevent them from happening, you can set "AUTO KEYSTONE" in the OPTION menu to "OFF" B The greater the correction of keystone distortion amount, the more the picture OSD POSITION Press the I or H buttons to move the OSD position. S4:3 The size of the input signal is compressed to 75% and projected. (This is useful for projecting a picture with a 4:3 aspect ratio onto a 16:9 screen. ) ASPECT This setting is only valid for an SVIDEO/VIDEO signal and a YPBPR signal in 525i (480i), 525p (480p) and 625i format. When a 4:3 signal is being input KEYSTONE Before carrying out keystone correction, 1) adjust the forward/back angle of tilt of the projector by pressing the adjuster buttons and 2) press the AUTO SETUP buttons to correct vertical keystone distortion. To release muting, set to "OFF" pressing the I or H buttons. SELECT:[^][@] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] Changing the display language Use the F and G buttons on the projector or remote control unit to select a language, then press the MENU button to accept the setting. LANGUAGE ENGLISH DEUTSCH FRANÇAIS ESPAÑOL ITALIANO SELECT:[^][@][{][}] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] AUTO SETUP This item functions in the same way as the AUTO SETUP button on the remote control unit. (page 14) FRAME LOCK If the picture's condition is bad while a RGB moving picture signal is projected, set the FRAME LOCK to "ON". Refer to page 61 on compatible RGB signals. 42 43 Basic Operation Option settings Select the item pressing the F or G buttons on the remote control unit or the projector. To make the SHUTTER or WEB PASSWORD (PT-L780NTU only) functions work, press the ENTER button. BACK COLOR OSD ON The current input name is displayed in the top-right corner of the screen when the input signal is changed. OFF Use this setting when you do not want the current input name to be displayed. This sets the colour which is projected onto the screen when no signal is being input to the projector. FRONT/REAR This setting should be changed in accordance with the projector setting-up method. Set to "FRONT" when using a normal reflective screen with the projector positioned in front of the screen, and set to "REAR" when using a translucent screen with the projector positioned behind the screen. for the lamp unit will be reset to zero. NOTE: B The lamp's operating life varies depending on the usage conditions (such as the LAMP POWER setting and the number of times the power is turned on and off). FAN CONTROL If using of this projector at high elevations (above 1 400 m), set the FAN CONTROL to "HIGH". OPTION SHUTTER OSD AUTO KEYSTONE RGB/YPbPr RGB2 SELECT BACK COLOR FRONT/REAR DESK/CEILING LAMP POWER LAMP RUN TIME NEXT PAGE @ SELECT:[^][@] ADJUST:[{][}] AUTO KEYSTONE OFF OFF RGB INPUT BLUE FRONT DESK LOW ON ON YPbPr OUTPUT BLACK REAR CEILING HIGH 10 H ENTER:[ENTER] ESC:[MENU] OPTION PREVIOUS PAGE ^ FAN CONTROL WEB CONTROL WEB STANDBY WEB PASSWORD CONTROL KEY FUNC1 SET ID AUTO POWER OFF STANDARD OFF OFF OFF MUTE ALL DISABLE HIGH ON ON ON KEYSTONE RGB/YPbPr This setting is valid when 750p, HDTV60, HDTV50, 525p, 625i and 525i signals are being input. The RGB/YPbPr item is displayed when an RGB1 IN, RGB2 IN or RGB 3 IN connectors has a signal being input. LAMP POWER This setting changes the lamp brightness. When set to "LOW", the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. If using the projector in small rooms where high luminance is not required, it is recommended that you set the LAMP POWER to "LOW". SELECT:[^][@] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] SHUTTER The shutter function can be used to momentarily turn off the picture and sound from the projector when the projector is not being used for short periods of time, such as during breaks in meetings or when carrying out preparation. [. . . ] B La lampe produisant la lumière est en verre; elle risque donc d'éclater si on la laisse tomber ou si elle heurte des objets durs. B La lampe usagée qu'on a retirée risque d'éclater si on la jette sans prendre de précautions. Jeter la lampe de la même manière qu'une lampe fluorescente. REMARQUE: B Le projecteur n'est pas fourni avec un bloc de lampe de rechange. [. . . ]