User manual PANASONIC PT-LC55E

[. . . ] You should note it in the space provided below and retain this booklet in case service is required. Important Information Model number: PT-LB90NTU/PT-LB90U/PT-LC55E/PT-LB75VU Serial number: WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. This LCD Projector is designed to operate on 100 V - 240 V, 50 Hz/60 Hz AC, house current only. Power Supply: CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire may result. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] (Available with signals of S-VIDEO/VIDEO only) Change setting AUTO SECAM PAL-N NTSC PAL-M Change setting NTSC4. 43 PAL Change setting ON OFF Automatic adjustment Active Deactive Note z AUTO mode is selected by default. z When the projector is not working properly in AUTO mode, change the setting according to each TV system type. Remarks z AUTO setting will automatically select the compatible signal from NTSC/NTSC 4. 43/PAL/PAL60/PAL-M/ PAL-N/SECAM. STILL MODE You can reduce the vertical flicker when projecting a still image. (Available with signals of S-VIDEO/VIDEO only) Change setting OFF ON Deactive Active Change setting RGB/YPBPR AUTO mode is selected by default. If the image is not projected normally in the AUTO mode, select RGB or YPBPR according to the input signal. The function becomes effective only when certain signals below are input. (VGA60, 480i, 576i, 480p, 576p, 1 080/60i, 1 080/50i, 720/60p, 720/50p) Select the signals to be input to the COMPUTER1 and COMPUTER2 IN terminal. Change setting AUTO RGB YPBPR Change setting Note z You must set to OFF when projecting a moving image. Automatic adjustment For RGB signals For YPBPR signals NOISE REDUCTION You can switch the automatic noise reduction system on/off. (Available with signals of S-VIDEO/VIDEO only) Change setting OFF ON Note z NOISE REDUCTION is set active when the selected Change setting No noise reduction Automatic noise reduction input signal has less noise. Applying noise reduction may affect the image quality, if so, set to OFF. ENGLISH - 31 Settings POSITION POSITION menumenu Navigating through the MENU (Æpage 27), select POSITION from the main menu and then select the required item from the sub-menu. z Set the selected item with buttons. SHIFT SHIFT H V 0 0 Remote control Control panel Horizontal (H): Press buttons to move the image horizontally. Remarks z The image cannot be moved while network signals z Press buttons to move the image. are input. REALTIME KEYSTONE If the projector is aligned non-perpendicularly to the screen, or if the projection screen has an angled surface, the keystone will be corrected automatically. ON OFF Warning messages will be displayed No display J INPUT GUIDE When you change the input method, the guidance appears in the upper right corner of the screen. The INPUT GUIDE will go out after 5 seconds without any operation. Note z When the WARNING MESSAGE is set to OFF, use the projector with utmost care due to the most of warning messages will not be displayed. CLOSED CAPTION SETTING If the input signal contains closed captions, you can turn on the feature and switch the channels. J CLOSED CAPTION OFF ON Deactive Active Settings Remarks z If you select the computer terminals which have no J MODE CC1 - 4 Remarks z VCR with TBC (Time Base Corrector) function is signals while INPUT GUIDE is set to DETAILED, the computer connection guidance will be displayed. You can switch the signals which output from the COMPUTER1/COMPUTER2 terminal by pressing the following computer key commands. Change the channels CC1 - 4 Q Computer connection guidance recommended for video cassette tapes. Manufacturer Panasonic NEC Acer HP SHARP TOSHIBA lenovo SONY Image output selection command Manufacturer DELL EPSON FUJITSU Apple Image output selection command + + + + + 36 - ENGLISH DISPLAY OPTION menu STARTUP LOGO You can set to display the Panasonic logo, your own image or Pre-set letters, when starting up the projector. Change setting ON TEXT USER OFF Change setting 4 ) Select OK and press the ENTER button to set the entered text in a box. 5 ) Select OK again and press the ENTER button. Select CANCEL or press the MENU/RETURN button to return to the previous menu without setting. Display "Panasonic" logo Display the original text Display the image registered by user No display AUTO SETUP You can turn off the automatic AUTO SETUP adjustment system. Change setting Change setting Remarks z If TEXT is selected, the input letters are displayed when starting up the projector. You can display 2 lines of original text which contain up to 40 characters each. z If USER is selected, the image transferred by the Logo Transfer Software is displayed when starting up the projector. (You can download the Logo Transfer Software from the Panasonic Projector website (http://panasonic. net/avc/projector/ download/). ) z STARTUP LOGO will be displayed for 30 seconds. AUTO When the projector detects a COMPUTER signal, automatically set the setting of SHIFT, DOT CLOCK and CLOCK PHASE in the POSITION menu. Only when the AUTO SETUP button is pressed, automatically set the SHIFT, DOT CLOCK and CLOCK PHASE in POSITION menu for COMPUTER signals. (Æpage 25) BUTTON J Editing the original text 1 ) Pressbuttons to select TEXT and press the ENTER button. 2 ) Pressbuttons to select the required line and press the ENTER button. You can enter and edit the texts for the first line in TEXT1 and the texts for the second line in TEXT2. STARTUP LOGO TEXT1 TEXT2 OK CANCEL SIGNAL SEARCH You can turn off the auto signal detecting system. [. . . ] Demander au centre technique agréé le plus proche de nettoyer le projecteur lorsque cela est requis. Se renseigner auprès du centre technique agréé pour le coût du nettoyage. Mise au rebut Pour connaître la procédure applicable, veuillez vous renseigner auprès des autorités locales compétentes ou de votre distributeur. Composants optiques FRANÇAIS - 65 Informations importantes Affichage à cristaux liquides Remplacement de la lampe Remplacement de l'unité de l'unité de la lampe J Filtre à air Le filtre à air doit être remplacé lorsque le nettoyage ne donne pas de bons résultats ou lors du remplacement de l'unité de lampe. Un filtre à air ainsi qu'une lampe de rechange sont fournis (ET-LAB80). S'adresser à un centre technique agréé pour commander le filtre à air en option (TXFMZ01VKG7). Informations importantes J L'unité de lampe L'unité de lampe ET-LAB80 a une certaine durée de vie et vous devez la remplacer régulièrement. [. . . ]