User manual PANASONIC PT-LM2E

[. . . ] Power Supply: This LCD Projector is designed to operate on 100 V ­ 240 V, 50 Hz/60 Hz AC, house current only. CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire may result. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] OFF "REALTIME KEYSTONE" is disabled. KEYSTONE When WIRELESS is selected This projector detects its own degree of tilt and corrects the keystone distortion automatically ("REALTIME KEYSTONE"). However, keystone distortion may still affect the images in some cases (e. g. when the projector is tilted slightly and the tilt is corrected slowly by hand or when the screen itself is tilted). In such cases, set "REALTIME KEYSTONE" to "OFF" and correct the vertical keystone distortion manually. 44-ENGLISH Picture condition Operation Press the F or Hbutton. NOTE: B Vertical keystone distortion can be corrected to ±30° of the angle of tilt. However, the greater the correction amount, the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as possible. B The picture size will also change when correction of keystone distortion is carried out. B The ratio of length and width of an image may become incorrect depending on the amount of the keystone correction. BYou can correct the keystone distortion manually when "REALTIME KEYSTONE" is set to "ON". However, when you turn on the power, the amount of correction will be reset and "REALTIME KEYSTONE" will function again if the tilt is different from the last time you used the projector. You can select the level of the input signal information. ON The "Panasonic" logo will be displayed when the power is turned on. OFF The "Panasonic" logo will not be displayed when the power is turned on. ENGLISH-49 Adjustments and settings NOTE: B If "INPUT GUIDE" is set to "DETAILED", the guide screen for computer connection will be displayed when PC1 or PC2 is selected and no signal is being input to the PC 1 IN or PC 2 IN connector. If you would like the guide screen not to be displayed, set "INPUT GUIDE" to "SIMPLE" or "OFF". POINTER SELECT LAMP POWER If you press the POINTER button on the remote control unit, the pointer will be displayed. You can select the pointer from 3 types as shown below (refer to page 35). A hand will be displayed. This setting changes the lamp brightness. When set to "ECOMODE", the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. If using the projector in small rooms where high luminance is not required, it is recommended that you set the "LAMP POWER" to "ECO-MODE". NOTE: B "LAMP POWER" cannot be set when no signal is being input. PC2 SELECT This setting is used to select the function of the PC 2 IN/PC 1 OUT connector. When set to "OUTPUT", it is set to the PC 1 OUT connector. LAMP RUNTIME This setting displays the usage time for the lamp unit which is currently being used. When replacing the lamp unit, follow the instructions on page 61, and reset "LAMP RUNTIME" to "0". NOTE: B The lamp's operating life varies depending on the usage conditions (such as the "LAMP POWER" setting and the number of times the power is turned on and off). 50-ENGLISH POWER OFF TIMER If no signal is input to the projector for the duration of the period you set, the projector will return to standby mode. [. . . ] La lampe s'éteindra automatiquement après environ 10 minutes lorsque la limite de 2 000 heures d'utilisation est atteinte, car le risque d'explosion de la lampe devient beaucoup plus grand passé cette limite. REMARQUE: B Les heures d'utilisation expliquées ci-dessus concernent l'utilisation lorsque "PUISSANCE DE LA LAMPE" dans le menu "OPTION" a été réglée sur "MODE STANDARD" et lorsque "AI" dans le menu "IMAGE" a été réglé sur "NON". Si "PUISSANCE DE LA LAMPE" est réglée sur "MODE ÉCO", ou si "AI" est réglé sur "OUI", la durée de vie de la lampe peut être allongée. B Bien que le délai de 2 000 heures soit l'intervalle de remplacement prévu, l'obtention de cette durée n'est pas couverte par la garantie. Notes sur le remplacement du bloc de lampe B La lampe produisant la lumière est en verre; il ne faut donc pas la laisser tomber ou la cogner contre des objets rigides, car elle risquerait d'éclater. [. . . ]