User manual PANASONIC TH-65PF20ER

[. . . ] Visit our Panasonic Web Site http://panasonic. net Table of Contents Important Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Accessories Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select the desired level by listening to the sound. Sound Normalise Normal 1/2 Normal 0 0 0 0 Off Sound Mode Bass Mid Treble Balance Surround 3 Item Sound Mode Bass Mid Treble Balance Surround Press to exit from adjust mode. Select On or Off. Note: Bass, Mid, Treble and Surround settings are memorized separately for each Sound Mode. Helpful Hint ( / Normalise Normalisation) While the "Sound" menu is displayed, if either the N button on the remote control is pressed at any time or the ACTION ( ) button is pressed during "Normalise", then all adjustment values are returned to the factory settings. SDI Sound Output This menu is available only when selecting a slot that any of the following terminal boards is installed: HD-SDI Terminal Board with audio (TY-FB10HD), Dual Link HD-SDI Terminal Board (TY-FB11DHD), or Dual HD-SDI Terminal Board for 3D (TY-FB30DHD3D) SDI Sound Output Left Channel Right Channel Sound Out Level Meter 2/2 Channel 1 Channel 1 Off Off Item Left Channel Right Channel Sound Out Details Channel 1 to Channel 16 Selects left audio channel. Disables audio output. Level Meter Off 1-8ch 9-16ch Sets audio channels to show in the audio level meter. 8 channels are displayed in the audio level meter; 4 channels each on both right and left sides of the display. 1-8ch: Displays the audio level meter (1-8ch) 9-16ch: Displays the audio level meter (9-16ch) 33 PRESENT TIME Setup / Set up TIMER The timer can switch the Plasma Display On or Off. Before attempting Timer Set, confirm the PRESENT TIME and adjust if necessary. Then set POWER ON Time / POWER OFF Time. 1 2 Press to display the Setup menu. Press to display the Set up TIMER screen or PRESENT TIME Setup screen. Setup MULTI DISPLAY Setup Portrait Setup Set up TIMER PRESENT TIME Setup Network Setup Display orientation 2/2 Landscape PRESENT TIME Setup 1 Press to select DAY or PRESENT TIME. PRESENT TIME Setup PRESENT TIME MON 99:99 Press to setup DAY or PRESENT TIME. Set button: Forward MON DAY button: Back 99:99 PRESENT TIME Notes: · Pressing " " or " " button once changes PRESENT TIME 1 minute. · Pressing " " or " " button continuously changes PRESENT TIME by 15 minutes. 2 Press to select Set. · Unless setting the present time other than "99:99", "DAY" and "PRESENT TIME" cannot be set. Note: When the display is turned off, the Scrensaver will be deactivated. 36 Screensaver (For preventing image retention) Setup of Screensaver Time After selecting Time Designation, Interval or Standby after SCR Saver, the relevant Time Setup will become available for selection and the Operating Time may be set. (Time cannot be set when "Mode" is "On" or "Off". ) Press to select Start Time / Finish Time (when Time Designation is selected). Press to select Periodic Time / Operating Time (when Interval is selected). Press to select Screensaver duration (when Standby after SCR Saver is selected). button: Forward button: Back Screensaver PRESENT TIME Start Function Mode Start Time Finish Time 15:00 Scrolling bar only Time Designation 6:15 12:30 Screensaver PRESENT TIME Start Function Mode Periodic Time Operating Time Scrolling bar only Interval 12:00 3:00 15:00 Notes: · Pressing " " or " " button once changes the Time 1 minute. [However, switching occurs every 15 minutes when Periodic Time is selected. ] · Pressing " " or " " button continuously changes the Time by 15 minutes. · "Screensaver duration" of the "Standby after SCR Saver" can be set from 0:00 to 23:59. When this is set to "0:00", " Standby after SCR Saver" will not be activated. Note: Timer function will not work unless "PRESENT TIME" is set. Screensaver PRESENT TIME 15:00 Start Scrolling bar only Function Standby after SCR Saver Mode 6:15 Screensaver duration 37 Reduces screen image retention Extended life settings The following settings are setup to reduce image retention: Setup 3D Settings Signal Screensaver Extended life settings Input label Component/RGB-in select Power save Standby save PC Power management DVI-D Power management No signal power off No activity power off OSD Language RGB Off On Off Off Disable Enable English (UK) 1/2 Extended life settings Express settings Custom settings Reset Set to the recommended value Set individually Reset to the factory settings Extended life settings Recommended settings Picture Mode Contrast Side panel NANODRIFT Saver Peak limit Lock settings Apply to current input Apply to all inputs Dynamic 30 High Mid Off unlock Image Retention Reduction Menu Image Retention Reduction Menu "Extended life settings" enables you to set the following 5 menus (Image Retention Reduction Menu) as recommended values or set them individually. Picture Mode Contrast "Picture Mode" and "Contrast" are same as "Picture" menu items (see page 28). The settings of this menu will be reflected to the "Picture" menu. [. . . ] Press to select "OSD Language". 3D Settings Signal Screensaver Extended life settings Input label Component/RGB-in select Power save Standby save PC Power management DVI-D Power management No signal power off No activity power off OSD Language Options Shipping Press for more than 3 seconds. 3 Press to select "Shipping". RGB Off On Off Off Disable Enable English (UK) Press to display the Shipping menu. Press to select "YES". 4 Shipping YES NO Press to confirm. 5 6 Wait for 10 seconds. Press the power switch ( ) on main unit to turn the power off. [from the unit] 1 Press the MENU button till the Setup menu is displayed. 2 Press the Volume Up"+" or Down"­" button to select "OSD Language". 3 Press and hold the ENTER button till the Shipping menu is displayed. [. . . ]