User manual PANASONIC WV-CP470

[. . . ] Colour CCTV Cameras WV -CP 470 Operating Instructions Model No. WV-CP470 WV-CP474E (Lens: Option) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. N0102-1042 V8QA5955BN Printed in Japan N 19 CP4 70 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende normer eller andre normgivende dokumenter som fælger bestemmelsene i direktiven 73/23/ EEC og 89/336/EEC. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de bepalingen van Richtlijnen 73/23/ EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med den følgende standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/ EEC og 89/336/EEC. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] ALC Mode with SUPER-D2 OFF and ELC Mode Note: If ELC is selected, set MASK SET according to this procedure. (When you select ELC, SUPER-D2 is not available. ) The MASK SET appears on the menu. ** ALC CONT ** BACK LIGHT COMP SUPER-D2 MASK SET LEVEL . . . I. . . . . The cursor is blinking in the upper left corner of the screen. RET Blinking 3. Move the cursor to the area where backlight is bright and press I to mask that area. (When the cursor is moved on an area that has already been masked, the mask and cursor start blinking. ) Blinking 4. If you want to change the video output level (picture contrast), move the "I" cursor for LEVEL and adjust the level. Note: If ON is selected for SUPER-D2, a shadow (black line) may appear at the boundary between the bright and the dim scene. This is a natural phenomenon and does not indicate trouble. Turns to white Blinking 3. Shutter Speed Setting (SHUTTER) Note: When ELC is selected for ALC/ELC on the CAM SET UP menu or ON is selected for SUPER-D2 on the ALC CONT menu, this item is not available. To select electronic shutter speed, select OFF for SUPER-D2 in the ALC CONT menu. The preset values for SHUTTER (electronic shutter speed) change by pressing L or M as follows: OFF (1/50) 1/120 1/250 1/500 The factory default setting is ---. 1/10000 1/4000 1/2000 1/1000 4. Gain Control Setting (AGC ON (DNR-H, DNR-L)/OFF) AGC (Automatic Gain Control) automatically controls the gain (an image brightness level). Move the cursor to AGC and select automatic level adjustment ON (DNR-H), ON (DNR-L), or OFF. ON (DNR-H): This setting raises the gain and brightens the image under low light conditions. ON (DNR-L): This setting reduces an afterimage sometimes caused by a moving object when ON (DNR-H) is activated. Notes: · When ON (DNR-L) is selected, noise can slightly increase than ON (DNR-H). · DNR-H and DNR-L do not appear on the system status display of the connected equipment. 5. Electronic Sensitivity Enhancement (SENS UP) There are two modes for SENS UP. AUTO: If you select X10 AUTO, for example, the sensitivity is automatically raised to X10 max. FIX: If you select X32 FIX, for example, the sensitivity is raised to just X32. Move the cursor to SENS UP and select the parameter for electronic sensitivity enhancement. The preset values for SENS UP (electronic sensitivity enhancement) change by pressing L or M as shown right: OFF X32 FIX X2 AUTO X16 FIX X4 AUTO X10 FIX X6 AUTO X6 FIX X10 AUTO X4 FIX X2 FIX OFF Notes: · When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this item. [. . . ] Select DC if you are using the auto iris lens that requires a DC drive signal. Select VIDEO if you are using the auto iris lens that requires a video drive signal. 10. Special Menu This menu lets you adjust and set up the video signal of the camera to meet your requirements. Move the cursor to END in the bottom ** CAM SET UP ** ** SPECIAL ** line of the CAM SET UP menu and CAMERA ID OFF UP SIDE DOWN OFF ALC/ELC ALC press L and M simultaneously CHROMA GAIN . . . . I. . . . [. . . ]