User manual PENTAX 28MM SHIFT LENS

[. . . ] Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. Regarding trademarks · PENTAX and Optio are trademarks of HOYA CORPORATION. · ArcSoft®, and its logo are either the registered trademark or trademark of ArcSoft Inc. · Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries. [. . . ] Press the four-way controller (5). A pull-down menu appears. Use the four-way controller (23) to change the number of recorded pixels. Recordable Image No. Recorded Pixels White Balance Focusing Area AE Metering Sensitivity EV Compensation MENU Cancel 12M 12M 7M 5M 3M 12 OK OK 5 6 Press the 4 button. The setting is saved. Press the 3 button. The camera returns to capture status. 105 3 Taking Pictures 106 · The number of recorded pixels for images captured in 9 (Green) mode is fixed at E. · The number of recorded pixels for images captured in C (Half-length Portrait) or N (Frame Composite) is fixed at h. · The number of recorded pixels for images captured in c (Digital SR) or X (Digital Wide) mode is fixed at f. (The number of recorded pixels will be h if you exit the X mode without taking the second picture. ) · The number of recorded pixels for images captured in W (Blog) is fixed at m. · If you change the [Recorded Pixels] setting frequently, you can save time by assigning it to the Green button (p. 119). Setting the Exposure (EV Compensation) You can adjust the overall brightness of the picture. Use this function to take pictures that are intentionally overexposed or underexposed. 1 2 3 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [EV Compensation]. Use the four-way controller (45) to select the EV value. To brighten, select a positive (+) value. You can choose the EV setting in the range of ­2. 0 EV to +2. 0 EV in 1/3 EV steps. Rec. Mode 1/3 Recorded Pixels 12M White Balance AWB Focusing Area AE Metering Sensitivity Auto EV Compensation 0. 0 MENU Exit 4 Press the 3 button. The camera returns to capture status. · When the histogram is displayed in still picture capture mode/playback mode, you can check the exposure (p. 26). Mode 1/3 Recorded Pixels 12M White Balance AWB Focusing Area AE Metering Sensitivity Auto EV Compensation 0. 0 MENU Cancel OK OK 3 Taking Pictures 5 6 Press the 4 button. The setting is saved. Press the 3 button. The camera returns to capture status. · When the shutter release button is pressed halfway, the brightness is metered and the exposure is determined. · When the subject is outside the focusing area and you want to use N (Spot AE metering), aim the camera at the subject and press the shutter release button halfway to lock the exposure, then compose your picture again and press the shutter release button fully. · Depending on the selected shooting mode, the AE metering setting may not be changed. Refer to "Functions Available for Each Shooting Mode" (p. 224) for details. · If you change the [AE Metering] setting frequently, you can save time by assigning it to the Green button (p. 119). Saving the AE Metering setting 1p. 125 111 Setting the Sensitivity You can select the sensitivity to suit the brightness of the surroundings. Auto The sensitivity is automatically adjusted by the camera. (Sensitivity 80 - 800) 80 The lower the sensitivity, the less noise that affects the image. 200 400 800 1600 Higher sensitivity settings use faster shutter speeds in low light 3200 conditions to reduce camera shake, but the image may be affected by noise. 6400 3 Taking Pictures 112 1 2 3 4 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Sensitivity]. Press the four-way controller (5). A pull-down menu appears. Use the four-way controller (23) to change the sensitivity. Rec. [. . . ] Each product marketed is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on the statistical basis as required by 47CFR §2. 909. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The above named party is responsible for ensuring that the equipment complies with the standards of 47CFR §15. 101 to §15. 109. Product Name: PENTAX Digital Still Camera Model Number: Optio H90 9 Appendix 244 Contact person: Customer Service Manager Date and Place: January 2010, Colorado Information for Users on Collection and Disposal of Old Equipment and Used Batteries 1. [. . . ]