User manual PENTAX IQZOOM 160
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PENTAX IQZOOM 160. We hope that this PENTAX IQZOOM 160 user guide will be useful to you.
Manual abstract: user guide PENTAX IQZOOM 160
Detailed instructions for use are in the User's Guide.
[. . . ] Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. Regarding trademarks · PENTAX is a trademark of HOYA CORPORATION. · , the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. · Eye-Fi, the Eye-Fi logo and Eye-Fi connected are trademarks of Eye-Fi, Inc. [. . . ] When using the flash at an extremely close distance, a shadow of the lens may appear in the picture taken.
1
Press the b button.
The flash pops up and begins charging.
b button
2
Press the four-way controller (4) in A mode.
The [Flash Mode] screen appears.
Flash Mode sh Mo Auto Au
3 Taking Pictures
MENU Cancel Cance cel
OK
OK
3 4
Use the four-way controller (45) to select a flash mode. Press the 4 button.
The setting is saved and the camera returns to capture status.
About the red-eye phenomenon
Taking pictures using the flash may cause the subject's eyes to appear red in the resulting picture. This phenomenon occurs when the light from the flash is reflected in the subject's eyes. It can be reduced by illuminating the area around the subject or moving closer to the subject and zooming out to a wider angle. Setting the flash mode to c, d or H is also an effective way of reducing red eyes. If the subject's eyes appear red despite such precautions, they can be corrected by the red-eye compensation function (p. 184). Saving the Flash Mode setting 1p. 144
113
To Use the Flash
1 2
Select a capture mode. (Not displayed in , mode)
3 Taking Pictures
114
3 4 5
Press the shutter release button halfway.
The focus frame (or face detection frame) on the display turns green when the camera focuses on the subject at the correct distance.
Press the shutter release button fully.
The flash discharges and the picture is taken.
Push the flash down to retract.
Selecting the Focus Mode
= q I s \ J
Use this mode when the distance to the subject is 40 cm (16 in. ) or Standard more. The camera is focused on the subject in the autofocus area when the shutter release button is pressed halfway. The camera is focused on the subject in the autofocus area when the shutter release button is pressed halfway. 1cm This mode is used for taking pictures of the subject from a distance Macro of 1 cm to 30 cm. The focus assist light is emitted from the self-timer lamp part.
4
Use the four-way controller (23) to select [Focus Assist].
AF Setting Focusing Area Auto Macro Focus Assist
MENU
5
Use the four-way controller (45) to select O or P.
O Focus assist light is emitted as necessary. (Default setting) P Focus assist light is not emitted.
The setting is saved.
6
Press the 3 button twice.
The camera returns to capture status.
119
· Looking at the light directly does not pose a safety hazard. However, do not look directly into the emitter from a very short distance. · The camera does not emit the focus assist light under the following conditions: - when the capture mode is set to C (Movie) - when s (Infinity) or \ is selected as the focus mode
Setting the Image Tone
3 Taking Pictures
120
Set the image tone of still pictures. You can select from [Bright] (Default setting), [Natural] or [Monochrome].
1 2 3 4
Press the 3 button in A mode.
The [A Rec. Mode] menu appears.
Use the four-way controller (23) to select [Image Tone]. Press the four-way controller (5).
A pull-down menu appears.
Use the four-way controller (23) to select a finishing tone.
Rec. Mode Image Tone Recorded Pixels Quality Level White Balance Sensitivity ISO Corction in AUTO
MENU Cancel
1/4
Bright Natural Monochrome AWB AUTO ISO80-400
OK
OK
5 6
Press the 4 button.
The setting is saved.
Press the 3 button.
The camera returns to capture status.
When [Monochrome] is selected, [Tone Adjustment] appears on the [A Rec. Mode] menu for setting the tone of monochrome images instead of [Saturation].
Selecting the Recorded Pixels
You can choose from nine recorded pixels settings for still pictures. The larger the number of recorded pixels, the clearer the details will appear when you print your picture. As the quality of the printed picture also depends on the image quality, exposure control, resolution of the printer, and other factors, you do not need to select more than the required number of recorded pixels. [. . . ] If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. 9 Appendix
262
For Switzerland: Used electrical/electronic equipment can be returned free of charge to the dealer, even when you don't purchase a new product. Further collection facilities are listed on the home page of www. swico. ch or www. sens. ch. Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a designation for the chemical element or compound in use. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PENTAX IQZOOM 160
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PENTAX IQZOOM 160 will begin.