User manual PENTAX OPTIO RZ10

[. . . ] ENG Digital Camera Operating Manual To ensure the best performance from your camera, please read the Operating Manual before using the camera. Thank you for purchasing this PENTAX Digital Camera. Please read this manual before using the camera in order to get the most out of all the features and functions. Keep this manual safe, as it can be a valuable tool in helping you to understand all the camera's capabilities. Regarding copyrights Images taken with the PENTAX Digital Camera that are for anything other than personal enjoyment cannot be used without permission according to the rights as specified in the Copyright Act. Please take care, as there are cases where limitations are placed on taking pictures even for personal enjoyment during demonstrations, performances or of items on display. [. . . ] Use the four-way controller (45) to select O or P. O P Blink Detection function works. Mode 2/3 Movie D-Range Setting Shake Reduction CCD-Shift Blink Detection Digital Zoom Instant Review MENU The setting is saved. Exit 4 Press the 3 button. The camera returns to capture status. Blink Detection 1p. 69 115 Setting the Shake Reduction Function You can set this function to correct camera shake which can occur during shooting. You can correct camera shake using optical shake reduction only (CCD-Shift), or the both optical and electronic shake reductions (Dual). The default setting is the optical shake reduction only (CCD-Shift). CCD-Shift Dual Off Optical shake reduction only is used. No shake reductions are used. 3 Taking Pictures 116 Use the Movie SR function (p. 128) to correct camera shake in C (Movie) mode. 1 2 3 4 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Shake Reduction]. Press the four-way controller (5). A pull-down menu appears. Use the four-way controller (23) to choose the Shake Reduction setting. Rec. Mode 2/3 Movie D-Range Setting Shake Reduction CCD-Shift Blink Detection Dual Off Digital Zoom Instant Review MENU Exit 5 6 Press the 4 button. The setting is saved. Press the 3 button. The camera returns to capture status. One of the following icons appears on the display. M l When the shutter release button is pressed halfway with [Shake Reduction] set to [CCD-Shift] or [Dual]. (If the camera shake is likely to occur, f is indicated when the shutter button is pressed halfway. ) · When [Shake Reduction] is set to [Dual], camera shake is corrected after shooting, and then the corrected image is saved. · When [Shake Reduction] is set to [CCD-Shift], CCD shifting sound may occur during shooting with C Burst Shooting(H). In the following situations, [Shake Reduction] cannot be set to [Dual] (only [CCD-Shift] or [Off] can be selected in the pull-down menu. ). If [Shake Reduction] is set to [Dual] beforehand, setting automatically changes to [CCD-Shift]. - When C (Movie), S (Fireworks), N (Frame Composite), X (Digital Wide) or F (Digital Panorama) mode is selected as the shooting mode - When g (Self-timer), j (Continuous Shooting), A (Burst Shooting(L)), B (Burst Shooting(M)) or C (Burst Shooting(H)) is selected as the drive mode - When the flash discharges - When the shutter speed is slower than 1/4 sec. - When the sensitivity is set to 1600 or higher - During Voice Recording 3 Taking Pictures Setting the Instant Review Use this setting to specify whether or not an Instant Review is displayed immediately after images are taken. The default setting is O (On). 1 2 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Instant Review]. 117 3 Use the four-way controller (45) to select O or P. O P Instant Review is displayed. Mode 2/3 Movie D-Range Setting Shake Reduction CCD-Shift Blink Detection Digital Zoom Instant Review MENU Exit 4 3 Taking Pictures Press the 3 button. The camera returns to capture status. Instant Review 1p. 69 If the Blink Detection function worked when shooting, the message [Closed eyes have been detected] appears for 3 seconds during Instant Review. Setting the Image Sharpness (Sharpness) You can give the image sharp or soft outlines. 1 2 3 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Sharpness]. Use the four-way controller (45) to change the sharpness level. F G H Soft Normal Sharp Rec. Mode Memory Green Button Sharpness Saturation Contrast Date Imprint MENU Exit 3/3 Off 4 Press the 3 button. The camera returns to capture status. If you change the [Sharpness] setting frequently, you can save time by assigning it to the Green button (p. 121). 118 Setting the Color Saturation (Saturation) You can set the color saturation. 1 2 3 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Saturation]. [. . . ] In the European Union These symbols on the products, packaging and/or accompanying documents mean that used electrical and electronic equipments and batteries should not be mixed with general household waste. Used electrical/electronic equipments and batteries must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of these products. Following the implementation by member states, private households within the EU states may return their used electrical/electronic equipments and batteries to designated collection facilities free of charge*. In some countries your local retailer may also take back your old product free of charge if you purchase a similar new one. [. . . ]