User manual PHILIPS 32PFL3406H

[. . . ] Register your product and get support at www. philips. com/welcome 47PFL4606H 46PFL5606H 42PFL4x06H 42PFL3x06H 40PFL5xx6H 37PFL4606H 32PFL5x06H 32PFL4606H 32PFL3x06H 26PDL49x6H 22PDL49x6H DesignLine Tilt EN User manual EN Addendum When you select a channel from the channel grid, a preview is not displayed. Dodatek Pi výbru kanálu z mízky není náhled zobrazen. Tillæg Når du vælger en kanal fra kanaloversigten, er der ikke nogen eksempelvisning. Nachtrag Wenn Sie einen Sender aus der Senderliste auswählen, wird keine Vorschau angezeigt. [. . . ] Select [Automatic] or [Manual], then press OK. Change the time zone Note · This option is only available if you select [Auto clock] > [Automatic] (in countries with clock transmission data). Automatically switch the TV to standby (sleep timer) Sleep timer switches the TV to standby after a pre-defined duration. Tip · You can switch off your TV earlier or reset the sleep timer during the countdown. 1 2 3 4 Press . Select [Setup] > [TV settings] > [Preferences] > [Clock] > [Time zone]. Press OK to confirm. Use daylight saving Note · This option is only available if you select [Auto clock mode] > [Manual]. 1 2 3 4 Press . Select [Setup] > [TV settings] > [Preferences] > [Sleep timer]. » The TV switches to standby after the specified time. 1 2 3 Press . Select [Setup] > [TV settings] > [Preferences] > [Clock] > [Daylight saving], then press OK. Select [Standard time] or [Daylight saving time], then press OK. EN 21 Lock unsuitable content You can prevent your children from watching certain programmes or channels by locking the TV controls. 6 To activate the locks, switch the TV on and off. » When you switch channels with CH - or CH +, the locked channels are skipped. » When you access the locked channels from the channel grid, you are prompted to enter your PIN code. Set or change code 1 2 Press . 3 4 Select [Setup] > [Channel settings] > [Child lock]. » Follow the on-screen instructions to create or change your PIN code. Tip Set parental ratings Some digital broadcasters rate their programmes according to age. You can set your TV to display only programmes with age ratings lower than your child's age. 1 2 3 4 5 Press . Select [Setup] > [Channel settings] > [Child lock] > [Parental rating]. Press to exit. · If you forget your code, enter `8888' to override any existing codes. 1 2 3 Lock or unlock one or more channels Press . Select [Setup] > [Channel settings] > [Child lock] > [Channel lock]. » The first time you lock or unlock a channel, you are prompted to enter your PIN code. Repeat the process to lock or unlock more channels. View Scenea You can display a default picture as the wallpaper on your TV. Otherwise, it is displayed for the duration of the sleeptimer. Switch on Scenea 4 5 1 2 Press . Select [Scenea], then press OK. » If a customised Scenea picture is loaded, that picture is displayed (see `Customise the Scenea picture' on page 23). 22 EN Customise the Scenea picture You can load another picture as the wallpaper. Note · When you load a new Scenea picture, it overrides the · To use another picture as the wallpaper, you need a current Scenea picture. USB storage device that contains a picture that is less than 1 MB in size. Change audio language You can choose an audio language if it is available from your broadcaster. For analogue channels, two languages may be available. English 1 2 3 While you watch TV, press OPTIONS. 1 2 3 4 5 6 7 Load a picture smaller than 1MB in size into a USB storage device. Press any button to exit Scenea. For digital channels, select [Audio language], select the language, then press OK. For analogue channels, select [Dual I-II], select either language, then press OK. Show or hide subtitles 1 2 While you watch TV, press SUBTITLE. · [On during mute]: When audio is muted, display subtitles. Note Change language Depending on your broadcaster, you can change the audio language, subtitle language, or both, for a TV channel. Multiple audio languages, subtitles, or both, are broadcast through teletext or DVB-T digital broadcasts. Dual sound broadcasts: With digital broadcasts, you can select a subtitle language. · Repeat this procedure to enable subtitles on each · Select [Subtitles] > [Subtitles off] to disable subtitles. analogue channel. Select a subtitle language in digital channels Note · When you select a subtitle language in a digital TV channel as described below, the preferred subtitle language set in the installation menu is temporarily overruled. Change menu language 1 2 3 Press . Select [Setup] > [TV settings] > [Preferences] > [Menu language], then press OK. Select a language, then press OK. 1 2 3 4 While you watch TV, press Select a subtitle language. [. . . ] The TV did not save your picture settings: · Check that the TV location is set to the home setting. The picture does not fit the screen; it is too big or too small: · Try using a different picture format. The picture position is incorrect: · Picture signals from some devices may not fit the screen correctly. Check the signal output of the device. HDMI connection issues There are problems with HDMI devices: · Note that HDCP (High-bandwidth Digital Content Protection) support can delay the time taken for a TV to display content from a HDMI device. [. . . ]