User manual PHILIPS HD 8839

[. . . ] Register your product and get support at www. philips. com/welcome English 02 Type HD8838 SUP 037DRJ OPERATING INSTRUCTIONS 02 EN READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE. IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. Close supervision is necessary when the appliance is used by or near children. Allow to cool before putting on or taking off parts, and before cleaning the appliance. [. . . ] If you wish to interrupt hot milk brewing, press the " " button. · 13 · Milk, even UHT milk, goes bad easily at room temperature; therefore, it is recommended to DO NOT keep it at room temperature for long periods. Furthermore, the milk carafe has always to be put back in the fridge when it is not needed. It is also advisable to keep the parts in contact with the milk cleaned following the directions and recommendations described in these instructions. AUTOMATIC CLEANING FUNCTIONS Before entering the Stand-by mode, the machine automatically performs a short cleaning cycle in the milk brewing area. Moreover, after brewing any kind of milk-based beverage, the machine reminds the user to clean the parts that have been in contact with the milk. This warning does not block any function of the machine and can be deleted by pressing the right lower button every time it appears. Orange However, it is advisable to regularly clean the parts of the machine in contact with the milk following the instructions described in the "CLEANING OF THE MILK BREWING SYSTEM" section of the manual. FAST CLEANING (It is recommended to perform it after each milk brewing) Before performing this operation remove the milk carafe from the machine. Orange · 14 · After having brewed milk for some times, turn the main knob to the right as for hot water dispensing: the image "CLEAN+" will appear. Place a container under the dispensing spout and push the upper link button to start the cleaning operation. Then, bring the knob back to the central position to allow other brewing programmes. C L E A N I N G O F PERIODIC CLEANING (It is recommended to perform this cleaning every time the milk carafe is removed, when the milk system does not work properly or has milk deposits on it). It is recommended to regularly clean the parts for brewing and frothing milk by dismounting both the parts installed on the machine and those installed on the carafe. Dismount the parts installed on the machine according to the instructions showed in the following figures: T H E M I L K B R E W I N G S Y S T E M · 15 · PERIODIC CLEANING Proceed as follows for the parts installed on the carafe. · Lift the cover and pay attention that the wand does not splash the remaining milk. · Remove the wand from the cover. · Remove the pin: - Rotate it counter-clockwise. - Take off the pin from the cover. · Wash the cover and the carafe with lukewarm water. · Wash the wand and the pin of the machine by running lukewarm water inside the duct. · After rinsing and drying all components, assemble the pin on the cover: - Place the pin into the cover. Insert the wand in the cover FROM THE STRAIGHT-CUT END and place the cover over the milk container. These parts can also be washed in the dishwasher placing them in the cutlery basket so that they do not get lost. Otherwise, the best way to clean the above-mentioned components is to leave the dismounted parts for 30 min in a basinful of lukewarm water with the specific detergent Saeco Cleaning Powder. (Rinse the parts with running water before reassembling them on the machine). · 16 · Proceed as follows to complete the cleaning process: 1 Remove the top cover paying attention to the suction pipe. 2 Fill the container with lukewarm water: Do not exceed the MAX level indicated on the container. 3 Replace the suction pipe inside the container and close the cover by pressing it to the end. C L E A N I N G O F T H E M I L K B R E W I N G S Y S T E M Place the cup you use every day to enjoy your hot milk. Press the " Green " button until the following page is displayed. Press the " " button to start dispensing water. Dispensing will stop automatically. If you wish to interrupt water dispensing, press the " " button. · 17 · HOT WATER DISPENSING Warning: At the beginning, short spurts of hot water may come out. · Before dispensing hot water, check that the following icon is displayed: Green To reset the machine to normal operation turn the selector switch counterclockwise until it is set to the " " position. When the machine is ready, proceed as follows: · Place a container under the dispensing spout. Orange It may happen that, even though the selector switch has been turned, hot water does not come out and the following icon is displayed. Wait for the warm-up phase to end in order to obtain a flow of hot water from the dispensing spout. · Turn the selector switch clockwise and set it to the " position. Orange If the following icon is displayed, clean the dispensing spout. After placing an empty container press the " " button and wait until the dispensing is finished. Then, hot water may be dispensed. · The following icon will be displayed. Green Press the " " button to start dispensing hot water. · Pour the desired amount of hot water. [. . . ] Make sure that the machine is turned off and has cooled before performing this operation. The coffee blend is unsuitable, the coffee is not Change coffee blend or adjust the grind as explained in freshly roasted or the grind is too coarse. Descale the machine. The machine grinds the coffee beans but no coffee comes out. (See note) Coffee leaks out of the dispensing spout. Turn on the machine. [. . . ]