User manual PHILIPS MCM-206

[. . . ] Servicing is required when the apparatus has been damaged in any 4 EN power cord, plug or adaptor to disconnect this apparatus from the power. Caution · Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. · You should use caution or temporarily discontinue use in potentially hazardous situations. Do not use headphones while operating a motorized vehicle, cycling, skateboarding, etc. ; it may create a traffic hazard and is illegal in many areas. Hearing safety Listen at a moderate volume. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. The higher decibel ranges are offered for those that may have already experienced some hearing loss. [. . . ] Select a preset radio station. e USB · Select USB device source. EN 9 English g Disc compartment Overview of the remote control f DISPLAY · Select display information during play. Erase a program. 10 EN 3 Get started Caution · Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Connect power English Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial number of this apparatus. ___________________________ Caution · Risk of product damage!Ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the apparatus. When you unplug the AC power cord, always pull the plug from the socket. · Before connecting the AC power cord, ensure you have completed all other connections. Connect speakers 1 Connect the power adapter to · the DC IN jack on the rear of the main unit · the power socket. Install remote control batteries Note · Ensure that the colors of the speaker wires and terminals are matched. Caution · Risk of explosion!When the remote control is not used for long periods, remove the batteries. 1 2 Hold down the socket flap. · Insert the right speaker wires to " R", left speaker wires to "L". · Insert the red/blue wires to "+", black wires to "-". Insert 2 UM-4 AAA batteries with correct polarity (+/-) as indicated. EN 11 3 Close the battery compartment. Switch to standby 1 Press to switch the apparatus to standby mode. » The clock (if set) appears on the display panel. To switch the apparatus to Eco Power Standby mode: 1 Set clock 1 In standby mode, press and hold CLOCK on the main unit to activate the clock setting mode. · [SHUF REP ALL] (repeat all randomly): all tracks are played repeatedly in random order. To return to normal play, press REPEAT/ SHUFFLE repeatedly until play mode is no longer displayed. Display play information 1 During play, press DISPLAY/RDS repeatedly to select different play information. 2 Program tracks You can program a maximum of 20 tracks. 1 In CD/USB mode, at the stop position, press PROG to activate the program mode. to select 2 3 4 5 Press / to select a track number, then press PROG to confirm. To review the program, in the stop position, press and hold PROG for more than 2 seconds. 14 EN Note Tune to a radio station Note · For optimal reception, fully extend and adjust the position of the FM antenna. · You can program a maximum of 20 FM radio stations and 10 MW radio stations. 1 2 3 Tune to a radio station. Press to allocate a number (1 to 20) to this radio station, then press PROG to confirm. » The preset number and the frequency of the preset station are displayed. Repeat the above steps to program other stations. Note 1 2 Press TUNER to select the tuner source. » The radio tunes to a station with strong reception automatically. 4 3 Repeat step 2 to tune to more stations. · To tune to a weak station, press / repeatedly until you find optimal reception. · To overwrite a programmed station, store another station in its place. Program radio stations automatically Note · You can program a maximum of 20 FM radio stations and 10 MW radio stations. Select a preset radio station 1 In tuner mode, press preset number. to select a 1 In tuner mode, press and hold PROG for 2 seconds to activate automatic program mode. [. . . ] · As a power-saving feature, the unit switches off automatically 15 minutes after track play reaches the end and no control is operated. Remote control does not work · Before you press any function button, first select the correct source with the remote control instead of the main unit. · Reduce the distance between the remote control and the unit. 20 EN Insert the battery with its polarities (+/­ signs) aligned as indicated. · Aim the remote control directly at the sensor on the front of the unit. [. . . ]