User manual PHILIPS SWA7528S

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PHILIPS SWA7528S. We hope that this PHILIPS SWA7528S user guide will be useful to you.


PHILIPS SWA7528S : Download the complete user guide (139 Ko)

Manual abstract: user guide PHILIPS SWA7528S

Detailed instructions for use are in the User's Guide.

[. . . ] The following chart lists the remote component keys and what type of device each key will control: 7 MUTE Key Press MUTE once to turn sound off or on. 16 LIGHT Key Press LIGHT once to turn on or off the keypad backlight. 8 LAST Key Press LAST once to recall the last channel. SETTING UP YOUR REMOTE CONTROL Before using your new remote control, you will need to obtain and install new batteries, as described below. Then you'll also need to program the remote control with the correct code numbers for your specific components. See instructions starting on page 4. Key TV VCR CBL AUD Programmed to Control TV VCR or DVD Cable Box Amplifier/Receiver ABOUT BATTERIES Note: The remote requires two (2) new "AA" alkaline batteries (not supplied). Do not mix old and new batteries or mix alkaline with manganese-type batteries. NOTE: If you want the component keys to control other types of devices, you'll need to reassign the component keys. [. . . ] Press and hold SET (approximately 5 seconds) until the red light blinks twice, then release SET. Test the unit by pressing POWER and any Component key (e. g. , TV, VCR, CBL, etc. ). If the batteries are inserted correctly the red indicator light will blink once. 3 3. 4. Battery Saver The remote has a Time Out feature that will automatically deactivate the remote control if a key is depressed for more than 30 seconds. This feature will help conserve the battery life should your remote control get stuck in a place where keys remain depressed (e. g. , between the sofa cushions). 3 4 5. Aim the remote control at the component and press POWER ONCE. If it does not respond, repeat steps 2 and 3, trying each code for your brand until you find one that works. If it still does not work, try using Auto Scan (see below) on how to program your component. Repeat steps 1 through 5 for each component you want to program into the remote control. 1. 2. Press and hold SET until the red light blinks twice, then release SET. The red light will blink twice. 6. 3. NOTES: Press each key within 10 seconds of the previous entry. Otherwise, the remote control will exit the programming mode. If you press SET at any time (except during step 3), the remote control will exit the programming mode without saving your entries. To stop scanning channels, press SCAN. NOTE: If a code digit is "0" , the red light will not blink. 5. Use 2 for the second digit, 3 for the third digit and 4 for the fourth digit. To find codes of other components, repeat steps 1 through 5, but substitute the appropriate key (e. g. , VCR or CBL) for the component you are checking. As before, write down each four-digit code. 6. 3. Re-Assigning Component Keys The remote can be set up to control any combination of four home entertainment components. By following these instructions, you can re-assign or duplicate a component key onto an unused component key. Favorite Channel Scan The FAV CH Key can be pre-programmed with up to 10 of your favorite channels and scans these only. 1 On the remote control, press a component key once (e. g. , TV, VCR, CBL) . 5 6 2. 3. Press and hold SET until the red light blinks twice, then release SET. The red light will blink twice. QUICK FEATURES SETUP GUIDE This guide is provided here for your convenience as a quick reference for performing remote control sequences. 4. Enter first channel, e. g. , 07. For some component brands the ENTER key must be pressed after the digits, this will count as a key press. Skip Step 5 if ENTER is needed as next channel number will be ready to program without pressing SET. Note: If 3 digits plus an Enter is needed for newer TVs/Cable channels, these will not be programmed. [. . . ] In other words, VCR control "punches through" regardless of what mode is on. However, if AUD is the selected mode, the VCR Transport Keys will not control the VCR unless you press the VCR first. In these two modes, the VCR Transport Keys will operate the functions for the selected component. 1 2 3 4 5 Code Verification x2 x2 Press component key once (e. g. , TV). Repeat with 2, 3, and 4. Sleep Feature Press SLEEP key to activate your component's internal sleep timer. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PHILIPS SWA7528S




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PHILIPS SWA7528S will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.