User manual POLTI VAPORELLA PROF 306

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual POLTI VAPORELLA PROF 306. We hope that this POLTI VAPORELLA PROF 306 user guide will be useful to you.


POLTI VAPORELLA PROF 306 : Download the complete user guide (477 Ko)

You may also download the following manuals related to this product:

   POLTI VAPORELLA PROF 306 (474 ko)
   POLTI VAPORELLA PROF 306 (465 ko)
   POLTI VAPORELLA PROF 306 (480 ko)
   POLTI VAPORELLA PROF 306 (642 ko)
   POLTI VAPORELLA PROF 306 MISE EN ROUTE DE L'APPAREIL (470 ko)

Manual abstract: user guide POLTI VAPORELLA PROF 306

Detailed instructions for use are in the User's Guide.

[. . . ] Water by its nature contains magnesium, mineral salts and other deposits which in hard water areas can contribute to limescale build up in the tank. To avoid these problems, it is necessary to swill out with tapwater and empty the generator tank after every 3 or 4 uses. In very hard water areas we recommend the use of our KALSTOP FP 2003, a special natural-base decalcifier which inhibits and breaks down limescale, making it easy to remove just by swilling out the tank with a little tapwater. This is a preventive against scale build-up and protects the metal walls of the steam generator tank. KALSTOP is available from Polti dealers or by mailorder from your Polti Service Centre. [. . . ] Wait for the pressure indicator light (3b) and the "iron heating" indicator light (3a) to go out (about 15 minutes). Push button (3) on the iron to release bursts of steam from the holes on the soleplate. NOTE: during initial operation of the iron, a few drops of water mixed with steam may come out of the soleplate until the temperature stabilises. It is advisable to direct the first jets of steam onto an old cloth until a uniform stable jet of steam is obtained. · Press the iron switch (4), leaving the boiler button off (2). · Adjust the soleplate temperature turning the knob (1) setting to the temperature required according to the type of fabric. · · · · · · · · · · I M P O R TA N T Before leaving our factory all our products are rigorously tested. However, your VAPORELLA may contain some residual water in the boiler. PAT E N T E D S A F E T Y C A P / " WAT E R O U T " All Polti machines are equipped with the unique Polti patented safety cap, which prevents opening of the generator tank as long as there is any pressure remaining inside the tank. This is an important and indispensable safety device, and it is necessary to follow certain procedures when re-filling the tank. Press the steam request button on the iron (3) so as to fully exhaust the steam supply from the tank. When cool, proceed to carefully refill the tank as described in paragraph 1a of the section "PREPARATION FOR USE" in the instructions. If refilling the generator when not completely cooled, we recommend that you carefully pour only very small quantities of water at each pouring into the tank, so as to avoid spitting from the tank. P R E PA R AT I O N F O R U S E 1a. Unscrew the patented safety cap (5) and fill the boiler with about 0. 9 litres of water using the special funnel (9) making sure that it does not overflow (fig. However, as hard water by its nature contains limestone, which may cause a build-up of limescale in the tank, in hard water areas we recommend the use of our natural-base decalcifier KALSTOP FP 2003. Ensure the patented safety cap is fully and correctly screwed on, otherwise you may experience steam escaping from around the cap. Connect the power supply cable into an earthed power supply of the correct voltage. NOTE: during the filling operation, be careful that the water does not overflow as it may come out and wet the surface where Vaporella is laid. 3 ENGLISH VA P O R E L L A P R O F 3 0 6 I M P O R TA N T · · Do not leave the iron unattended whilst connected to the mains. Iron only on heat resistant surfaces and on surfaces that allow the steam to escape e. Ensure the patented safety cap is fully and correctly screwed on, otherwise you may experience steam escaping from around the cap. The pressure indicator light (3b) and the Iron heating indicator light (3a) goes on and off during usage. This means that the heating element is working correctly to keep a constant pressure in the boiler. [. . . ] · Green-and-yellow: Earth · Blue: Neutral · Brown: Live As the colours of the wires in the mains leads of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the letter "E" or by the earth symbol or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter "N" or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter "L" or coloured red. 4 AT T E N T I O N This appliance is built according to current regulations for recycling. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE POLTI VAPORELLA PROF 306




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual POLTI VAPORELLA PROF 306 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.