User manual ROSE DISPLAYS SUPERSNAP WITH ANOCONNECTORS
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ROSE DISPLAYS SUPERSNAP WITH ANOCONNECTORS. We hope that this ROSE DISPLAYS SUPERSNAP WITH ANOCONNECTORS user guide will be useful to you.
Manual abstract: user guide ROSE DISPLAYS SUPERSNAP WITH ANOCONNECTORS
Detailed instructions for use are in the User's Guide.
[. . . ] SuperSnapTM with AnoConnector Parts
Instruction Sheet
SuperSnap 12S300
Multi Clips 1UP-0100
6" Rod 97-0304-06
AnoConnector 06-2930
Instructions for assembly
Step 1
Slide MultiClip into top of the SuperSnap. Holding clip at a slight angle, first insert one round end, then press down on other round end and push MultiClip into position. [. . . ] 7 Note: It is easier to open and close the SuperSnap by starting at one end and working your way down the holder.
Step 6
Insert graphic into one section of SuperSnap (top and bottom). 8
Open all holders
Figure 7
Figure 8
Step 7
To close, snap the SuperSnap shut. Repeat steps 5-7 for hanging additional graphics.
Insert posters
Figure 9
Figure 10
Step 9
Push end caps into place. Finished Look
Important note:
Please save and reuse the SuperSnap, End Caps, AnoConnectors, and MultiClips for future projects.
Finished Look
Page 2 of 2
The SuperSnap and AnoConnector are trademarks of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSSuperSnapAnoConnector
35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com
Incept-9. 12. 02
SuperSnapTM with AnoConnector Parts
Instruction Sheet
SuperSnap 12S300
Multi Clips 1UP-0100
6" Rod 97-0304-06
AnoConnector 06-2930
Instructions for assembly
Step 1
Slide MultiClip into top of the SuperSnap. Holding clip at a slight angle, first insert one round end, then press down on other round end and push MultiClip into position. 3
Figure 1
Figure 2
Step 2
Insert AnoConnector into rail of one SuperSnap. 4
Figure 3 Figure 4
Step 3
Insert threaded rod halfway into clip rail of the same SuperSnap. 5
Step 4
Push the second piece of SuperSnap onto both AnoConnector and the threaded rod. 6 Repeat steps 2-4 for additional SuperSnaps.
Figure 5
Figure 6
Page 1 of 2
The SuperSnap and AnoConnector are trademarks of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. [. . . ] Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSSuperSnapAnoConnector
35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com
Incept-9. 12. 02 [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ROSE DISPLAYS SUPERSNAP WITH ANOCONNECTORS
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ROSE DISPLAYS SUPERSNAP WITH ANOCONNECTORS will begin.