User manual ROWENTA NG 9400 PERFECT PRO

[. . . ] Try to avoid ironing over zips which may have rough edges. The soleplate is scratched or damaged. You have placed your iron flat on a metallic rest-plate. You have ironed over a zip. I Problems? Problems Possible cause Solution Check that the mains plug is properly inserted or try plugging the iron into a different socket. As soon as the Thermostat light goes off, the set temperature has been reached. This is normal. If you have any further problems or queries with our products please call our Customer Relations team first for expert help and advice: HELPLINE: 0845 602 1454 ­ UK 01 4751947 ­ Ireland None or too little There is insufficient water in the water steam is being tank. [. . . ] During this time press the power steam button (3) from time to time to release several bursts of steam. Any particles released through the soleplate during first use are harmless and are due to the newness of your appliance. A Appliance description 6 Filling inlet (with push-button opening) 7 Spray nozzle 8 Mains supply cord 9 Water tank with maximum water level indicator 10 Soleplate (depending on model) 11 Flexible cord support B 1 Thermostat light 2 Spray button 3 Power steam button 4 Variable steam control 5 Temperature control dial C Filling / topping up water Before filling the water tank, pull out the mains plug and set the steam control to position . Close the filler inlet by pressing the push-button again, before returning the iron to the horizontal. However, if your water is very hard, you can mix it 50% untreated tap water with 50% distilled or demineralised water. Do not add anything to the contents of the water tank and do not use water from clothes dryers, scented or softened water, water from refrigerators, batteries or air conditioners, pure distilled water or rain water. These contain organic waste or mineral elements that become concentrated when heated and cause spitting, brown staining or premature wear to your iron. C D E E Safety instructions · The appliance complies with EU directives 72/23/EEC and 89/336/EEC. · The appliance may only be connected to alternating current as specified on the rating plate. · Do not leave the appliance unattended while it is connected to the mains supply. Always use the handles provided and warn other users of the potential dangers (e. g. · Always disconnect the appliance: ­ before filling or emptying the water tank; ­ before leaving the room (even for a short time); ­ after use. · An electrical appliance should not be used if: ­ the appliance, the supply cord or the cord protector is damaged; ­ the appliance has been dropped; ­ the appliance is obviously leaking. In this case the appliance should be returned to an approved Rowenta Service Dealer for repair. (See enclosed list for addresses. ) · Repairs to electrical appliances may only be carried out by specialists. To avoid danger to users, a defective or damaged supply cord may only be replaced by an authorised Rowenta service centre. Any commercial use, inappropriate use or failure to comply with the Instructions, the manufacturer accepts no reponsibility and the guarantee will not apply. · When the appliance has reached the end of its operational life it should be disposed of through the correct channels. · Due to the exceptional steam power, for best results we recommend that you use a vented/mesh ironing board. · Ensure garments are flat when ironing to avoid powerful steam venting sideways. · Be careful of hot steam when ironing close to the edge of the ironing board. 1 D Setting the temperature Ironing label Fabric Synthetic fibres, e. g. viscose, polyester, silk Temperature control F Wool Cotton, linen Using the temperature control dial, set the iron temperature to suit the type of material. [. . . ] - Press the power steam button repeatedly, moving the iron from top to bottom. The power steam and vertical steam functions (E 4) are also possible if the steam control is set to . E5 Spray function To dampen stubborn creases, press the spray button. F Additional functions F 1 Anti-Drip system Prevents water escaping from the soleplate when the temperature is too low. F 2 Anti-scale system Your iron contains an anti-scale cartridge to reduce scale deposits. [. . . ]