User manual ROWENTA RU5053EH PRO

[. . . ] DESCRIPTION 1 2 3 4 Lid of the vacuum cleaner Lid opening button Front Separation system a Separator with cones b Air/dust separation grid c Separation compartment Dust compartment Dust compartment filling maximum level Dust compartment housing Dust compartment opening button Dust compartment joints Carrying handle Suction opening On/Off pedal Cord winder pedal Parking position Rollers HEPA filter housing HEPA filter capsule (RS-RT3186) 18 Air outlet grid 19 Black foam filter (RS-RT3184) 20 Microfilter (RS-RT3185) Accessories 21 Flexible pipe with extra-long power nozzle and mechanical power regulator* 22 Crevice tool* 23 Telescopic crevice tool* 24 Brush* 25 Upholstery nozzle* 26 Accessory clip* 27 Telescopic tube* 28 Extension tubes* 29 All floor nozzle* 30 Delta nozzle* 31 Parquet nozzle* 32 Turbobrush* 33 Mini Turbobrush* 5 6 7 8 9 10 11 12 13 14 15 16 17 *Depending on model: this is either equipment specific to certain models or available as an optional accessory. 7 BEFORE USING FOR THE FIRST TIME 1 • Unpacking Unpack your appliance, keep your warranty card and read the instructions for use carefully before using your appliance for the first time. If you are using an extension cord, make sure it is in perfect condition and that it suitable for the power of your vacuum cleaner. Do not move the vacuum cleaner by pulling on the cord, the appliance must be moved by its carrying handle. [. . . ] Never operate the vacuum cleaner without the filtration system (foam, microfilter and filter). Never put the foam and the microfilter into the vacuum cleaner before they are completely dry. In the event that you find it difficult to obtain accessories and filters for this vacuum cleaner, contact the Rowenta customer service (see contact information on the last page). EN 2 • Tips and precautions USE 1 • Assembly of the parts of the appliance ATTENTION accessories. Clip the nozzle of the hose into the suction inlet located on the front of the vacuum cleaner (fig. €¢ For rugs and carpets: use the nozzle in the retracted brush position or the turbobrush* – (animal hair). €¢ For parquet and smooth floors: use the nozzle in brush position or, for a better result, use the parquet nozzle*. €¢ For corners and areas which are difficult to reach: us the crevice tool*. Always stop and unplug your vacuum cleaner before changing 2 • Connecting the cord and starting the appliance ATTENTION Never operate Unwind the power cord completely, plug your vacuum cleaner in and press the On / Off pedal the vacuum cleaner without the filtration system (foam, microfilter and filter). Adjust the suction power with the mechanical power regulator* on the power nozzle: open the slider on the power nozzle to manually reduce suction power, e. : on fragile *Depending on model: this is either equipment specific to certain models or available as an optional accessory. 33-34) - then replace the entire separation system (4a+4b+4c) in the vacuum (fig. EN 7 • Clean your vacuum cleaner Wipe the body of the vacuum cleaner and the accessories with a soft damp cloth, then dry using a dry cloth. iMPORTANT Do not use detergents or any corrosive or abrasive products. The transparency of the dust compartment and/or the front and/or lid may change over time. Remove the separation compartment (4c) by turning it slightly to the left (fig. 6 • Clean the separator (4) 10 TROUBLESHOOTING IMPORTANT As soon as your vacuum cleaner stops performing efficiently, and before making any checks, stop it by pressing on the On/Off pedal. If your vacuum cleaner does not start • The appliance is not powered. If there is no suction • An accessory, the tube, the flexible hose, the separator (4a), the air/dust separation grid (4b) or the separation compartment (4c) are blocked: unblock them. If your vacuum cleaner is not vacuuming properly or is making a whistling noise • An accessory, the tube, the flexible hose, the separator (4a), the air/dust separation grid (4b) or the separation compartment (4c) are partially blocked: unblock them. €¢ The vacuum cleaner lid is not properly positioned: close the lid tightly. €¢ The dust compartment is poorly positioned: put it back properly. [. . . ] If the floor nozzle is difficult to move • Close the mechanical power regulator* on the power nozzle. If the power cord does not wind up completely • The cord slowed down as it was winding up: bring the cord back out and press the cord winder pedal again. If the problem persists, take your vacuum cleaner to the nearest Rowenta Approved Service Centre. See the list of Rowenta Approved Service Centres or contact the Rowenta Consumer Service (see contact information on the last page). [. . . ]