User manual ROWENTA STEAM IRONS DX8000

[. . . ] Before plugging in, read the information about dual voltage operation in the instruction section of this manual. 2 SPECIAL INSTRUCTIONS 1. To avoid a circuit overload, do not operate a high wattage appliance on the same circuit. If an extension cord is absolutely necessary, a 10-ampere cord should be used. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. [. . . ] Place product on its side on a firm, heat resistant, flat surface, as soleplate will be hot. DUAL VOLTAGE 240 V 120 V Dual voltage selection The appliance can work on both, 120V or 240V, AC systems. Be sure the dual voltage selector (E) is in the correct voltage position before operating. To do this, unplug the appliance and turn the selector which is below the handle with a coin, so it is aligned with the correct voltage (either 120V or 240V). ! Never change selector while unit is plugged in. This is a 120/240 V dual voltage appliance and may be used in the United States and abroad without an electricity converter. An adapter plug may be necessary when using appliance in foreign countries. If needed, plug the steambrush into correct adapter plug for the specific country and plug assembly into electrical outlet. Dual voltage selector in wrong position If the voltage selector is set to 240 V in a 120 V supply, the performance of the Steambrush will be reduced. Never set the voltage selector to 120 V in a 220­240 V supply, as this can damage the product. FILLING THE WATER TANK Before plugging in the Steam 'n Press fill the water tank (C) with water as follows: Remove the water tank To remove the water tank, hold on to the bottom half of the handle and slide the top half of the handle away from the appliance as shown. 5 Filling the water tank Remove cap, fill the tank with ordinary tap water and close the cap. Replacing the water tank Put the full water tank back into the unit, by sliding the lower handle back into the top half of the handle until it is firmly in place. Adding water during use Always unplug the appliance and wait for it to cool down before removing the water tank. Plug in the appliance and wait approximately one minute to ensure your Steam 'n Press is fully reheated before using it. ATTACHING AND REMOVING THE SOLEPLATE COVER Attaching the soleplate cover The Steam 'n Press should be unplugged and completely cool when removing or attaching the soleplate cover. After treatment, let the article of clothing cool down on the hanger before wearing. ! Never steam clothes while they are being worn. Steaming drapes and upholstery Wrinkles and creases can be removed from drapes while they are hanging on the rods. Simply follow the procedure described in "Steaming clothes". When using the appliance horizontally return to the vertical position occassionally to ensure maximum steam performance. Lint pad Threads, lint and hair can easily be removed with the lint pad (H) by brushing the clothes slowly from left to right. The pad can be cleaned by brushing in the opposite direction right to left on a scrap of old cloth. AFTER USING THE STEAMBRUSH Set the temperature control dial (A) to min. Empty the water remaining in the tank and leave unit on its side to cool. min Storage After the appliance has cooled down, it may be stored in the bag provided. 9 CLEANING AND MAINTENANCE If the body and the handle become dirty they should be wiped with a damp cloth when the appliance is cold and unplugged. Cleaning the soleplate In normal use a draggy coating may build up on the soleplate (starch, detergent buildup, burnt synthetic fibers). This can be easily removed by using the Rowenta Soleplate Cleaning Kit or a quality hot iron soleplate cleaner available at most stores. To prevent scratching of the soleplate, do not iron over sharp objects (zippers, etc. ). WATER TO USE IN ROWENTA STEAM 'N PRESS Tap water The Rowenta Steam 'n Press is designed to be used with REGULAR TAP WATER (up to 12 grains of hardness). If your water is harder than this, Rowenta recommends mixing half tap water with half distilled water which reduces the hardness; or just use inexpensive bottled spring water. [. . . ] Once you have changed water it will take several uses to correct the problem. Rowenta recommends trying the steam function for the first time on an old towel or cloth to avoid damaging your clothes. Iron and other impurities If your water supply contains large amounts of iron or organic matter, these minerals can collect inside the appliance and eventually appear as brown stains. If you experience these problems, Rowenta recommends using inexpensive bottled spring water. [. . . ]