User manual RUSSELL HOBBS 14045

[. . . ] cleaning the car), connect it to the electricity supply via a residual current device (RCD), with a rated residual operating current not exceeding 30mA. 8 Keep an eye on the cable, so it doesn't catch on anything, or trip anyone up. 9 Don't try to use the cleaner on its end ­ it's not stable in this position ­ it'll topple. 11 Unplug the cleaner and rewind the cable when not in use, before moving and before cleaning. [. . . ] Slide the tab on top of the brush to 4 for floors without carpet, or carpet with short pile; slide it to 3 for rugs and long pile carpets 4 crevice tool as the name implies, down the sides of upholstery, in awkward spaces, nooks, and crannies nothing else can reach. small brush use it to remove pet hair, lint, and dust from blinds, curtains, and upholstery; to brush/clean awkward corners. To use, turn it a bit more than 90° from the crevice tool, to store, turn it back, parallel to the crevice tool. tubes 16 Fit the extendable tube for floors, carpets, or for those hard to reach places: a) grip the end of the inner tube in one hand, the outer tube in the other b) turn your right hand quarter of a turn anti-clockwise to unlock the tubes c) move the inner tube in or out to the length you require d) turn your right hand quarter of a turn clockwise to lock the tubes 17 Push the wide end of the extendable tube on to the nozzle. 18 Choose a tool, and push it onto the narrow end of the tube. suction control 19 The suction control is on the nozzle ­ move it towards the nozzle for maximum suction, away from the nozzle to reduce suction. plug in caution If you've accidentally pressed the on/off switch, the cleaner could come on when you plug it in. 20 Plug the cable into a socket near the area to be cleaned (switch the socket on, if it's switchable). 21 Press and release the on/off switch 3, to turn the cleaner on. switching on cleaning 22 Move the tool over the surface, cleaning a small area at a time. 23 When you move to a new area, overlap the previous area, to make sure none of the surface is missed. switching off 24 If you've finished, if you want to change tools, or if you just want to stop, press and release the on/off switch 3, to turn the cleaner off. 27 Stand clear of the cable, and press the cable rewind button, the cable will rewind back into the cleaner. If it catches on anything, stop pressing, and it'll stop rewinding. 29 We've tried not to make it too powerful, to avoid wrecking your home, so you may need to push the plug end into the storage area manually. finished cleaning? 5 removing and emptying the bin 30 You don't have to empty the bin after each use, but it's a very good idea. Your cleaner will happily work till it's chock full, but you'll be wasting energy swirling yesterday's dust around. 31 Switch off, unplug, and leave it for a minute, to let the dust settle. 32 Squeeze the locks on the hose end, and pull the hose out of the cleaner ­ this'll keep the hose out of your way. Use the other hand to raise the bin handle, then lift the bin up and out of the cleaner. 34 Lower the bin into your dustbin so it's below the rim ­ this'll stop the dust dispersing into your environment. The bottom of the bin will drop open, and the contents will drop into the dustbin. 36 Tap the bin lightly (over the dustbin) to dislodge any remaining dust. 37 Check the inlet for blockages, if there are any, give the bin a few taps to dislodge it. It's also a good idea to check the filter at this point (see "check the filters", below). 38 Lift the bottom of the bin to close it, and press the latch over the lugs on the edge of the bin bottom, to lock it closed. 39 Lower the bin into the cleaner, and lower the bin handle, to secure it. 40 Attach the hose to the cleaner. check the filters While emptying the bin give the filters a quick check. [. . . ] Keep an eye on it as you use it, and examine the filters when you empty the bin. If anything needs cleaning, do it there and then, don't put it off, in case you forget. · Wipeexternalsurfaceswithadampcloth. Adabofwashing-upliquidwillremove stubborn stains, but clean it off afterwards, or it may stain. · Wipethetoolswithadampcloth, orhandwashinwarmsoapywater. Rinseto remove any trace of soap, and air dry before using. [. . . ]