User manual SAMSUNG SR-8894-NAVIBOT

[. . . ] CAUTION/WARNING SYMBOLS USED WARNING WARNING Indicates that a danger of death or serious injury exists. Indicates that a risk of personal injury or material damage exists. CAUTION OTHER SYMBOLS USED NOTE Explains terms to help users understand how use the product properly. 2_ Safety information Safety information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR ROBOTIC VACUUM CLEANER. Unplug from outlet when not in use and before conducting maintenance. WARNING: to reduce the risk of fire, electric shock, or injury: GENERAL · · · · · · Use only as described in this manual. Do not operate the robotic vacuum cleaner or charger if it has been damaged in any way. If the cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, return it to a customer care center. [. . . ] There should be no obstacles 0. 5m to the left and right and within 1 m of the front. abo ut 0 . 5m abo ab ut 0 . 5m ou t1 m 3. Install the charger in a location where it can be easily accessed by the robotic vacuum cleaner. 4. When the floor is made of wood, install the charger in the same direction as the grain of the wood. NOTE Always keep the power cord of the charger plugged into the power outlet. - If no power is supplied to the charger, the robotic vacuum will not be able to find the charger and will not be able to charge automatically. - If the robotic vacuum cleaner is separated from the charger, the battery is automatically discharged. Operating the cleaner _21 Operating the cleaner INSTALLING THE ROBOTIC VACUUM CLEANER CHARGING When the product is initially purchased, the battery is fully discharged, and you must charge the robotic vacuum cleaner manually. OFF ON Power Lamp Charging Lamp Turn on the Power Switch at the bottom of the product. After aligning the charge pins of the main unit with the charge pin of the charger station, press the main unit until you hear a "Recharging power" sound from the charger. - When charging starts, the battery level indicator and " " will be displayed in sequence in the display panel. - When charging is complete, the battery level indicator and "FULL" will be displayed in the display panel. Flash Power Lamp Charging Lamp Charging <Charge display> Fully charged When the battery level display flashes while cleaning, the robotic vacuum cleaner stops vacuuming and automatically charges itself at the charger. Charge complete Charging Required charging Flash When the battery level flashes and "LO" is displayed while cleaning, robotic vacuum cleaner cannot be operated by the remote control or the buttons on the main unit. In this case, directly carry the robotic vacuum cleaner to the charger to charge the battery. (This is when the battery is completely discharged. ) NOTE When the product is initially purchased, it will take about 120 minutes to fully charge the battery and will run for about 90 minutes. Mode lamp operations - Fence (virtual wall) Mode: The red lamp flashes. Setting the mode - Whenever you press the Mode/Power button, Fence (virtual wall) mode Guard (virtual door) mode Power off is selected in this sequence. Setting the Fence length - Set the distance to restrict the access of robotic vacuum cleaner from the VIRTUAL GUARD using the distance control switch. Switch Setting Max About 1~2m About 2~3m About 3~4m · (Short) ·· (Medium) ··· (Long) 3 Distance Detection Sensor The distance detection sensor forms a virtual straight barrier of the specified fence length. Set the switch according to the required fence length. Forming a Fence (virtual wall) VIRTUAL GUARD creates an invisible barrier that the robotic vacuum cleaner cannot cross. Set the fence length using the distance control switch. A fence (virtual wall) is formed. Install the VIRTUAL GUARD in front of the area you want to block access from the robotic vacuum cleaner. - Install the VIRTUAL GUARD so that the distance detection sensor can form an invisible barrier that the robotic vacuum cleaner cannot cross. Operating the cleaner _25 Operating the cleaner Using Guard (virtual door) mode The VIRTUAL GUARD forms an invisible door that the robotic vacuum cleaner cannot cross until current room is completly cleaned. The VIRTUAL GUARD opens the invisible door when cleaning the of room is complete. - Install the VIRTUAL GUARD so that the distance detection sensor can form an invisible barrier that the robotic vacuum cleaner cannot cross. NOTE Room1 Room 2 Room 3 Charger VIRTUAL GUARD Distance Detection Sensor · When not using the VIRTUAL GUARD, turn the power off. (When not using the robotic vacuum cleaner for long periods of time, separate the batteries to avoid discharging them. ) · If the Mode/Power button does not work, it indicates that the batteries have worn out. (Specifications: Type D (LR20) alkaline batteries ) · You can additionally purchase a VIRTUAL GUARD from Samsung Electronics customer care Co. , Ltd. 30cm 30cm 0c c A guard (virtual door) is formed. Since an invisible barrier is formed to prevent the robotic vacuum cleaner from running against the VIRTUAL GUARD, installing the VIRTUAL GUARD within 30 cm of the outside walls is recommended. CAUTION About the IrdA sensor. [. . . ] · Is the robotic vacuum cleaner · Turn off the Power Switch and stuck on the doorsill?· Check whether the dust bin · Stop the robotic vacuum cleaner is full of dust. · Check whether the suction · Turn off the Power Switch and inlet is clogged by foreign remove the foreign substances substances. on the suction inlet. · Check whether the filter is · Clean the filter well. cleaner, and manually dock the robotic vacuum onto the charger to charge it. [. . . ]