User manual SAMSUNG SYNCMASTER T27B750ND

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SAMSUNG SYNCMASTER T27B750ND. We hope that this SAMSUNG SYNCMASTER T27B750ND user guide will be useful to you.


SAMSUNG SYNCMASTER T27B750ND : Download the complete user guide (8112 Ko)

You may also download the following manuals related to this product:

   SAMSUNG SYNCMASTER T27B750ND (8246 ko)

Manual abstract: user guide SAMSUNG SYNCMASTER T27B750ND

Detailed instructions for use are in the User's Guide.

[. . . ] >> Click here to see an animation clip Power button [ ] Use this button for turning the monitor on and off. Power Indicator This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments. Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods. Rear Note The configuration at the back of the monitor may vary from product to product. Simple Stand POWER port HAS Stand Connect the power cord for your monitor to the POWER port on the back of the monitor. [. . . ] Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury. · Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions. To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Please use Wall Mount according to the International standards. · · · 15 Connections SyncMaster 2243BW/SYNCMASTER T27B750ND Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. · Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector on the video card. · Connect the DVI Cable to the DVI IN Port on the back of your Monitor. [DVI IN] Connected to a Macintosh. · Connect the monitor to the Macintosh computer using the D-sub connection cable. Note If the monitor and the computer are connected, you can turn them on and use them. 16 Connections Using the Stand Monitor Assembly Simple Stand Monitor and Bottom HAS Stand HAS Stand A. Stand Stopper Attaching a Base This monitor accepts a 100. 0 mm x 100. 0 mm VESA-compliant mounting interface pad. 17 Connections Simple Stand A. Turn off your monitor and unplug its power cord. HAS Stand Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. If you still see an (error) message on the screen when the monitor is connected properly, check to see if the monitor status is set to analog. Press ` /SOURCE' button to have the monitor double-check the input signal source. Q: A: If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Timing Modes) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer. Q: A: A: Can you see "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz" on the screen?You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly. 54 Troubleshooting A: If the display exceeds SXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz" message appears for one minute and then disappears. (The message is displayed again if the system is rebooted. ) Q: A: A: A: Q: A: There is no image on the screen. [. . . ] (If it does, request an a service for the main board of the computer. ) If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver. Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz. (Do not exceed 75 Hz when using the maximum resolution. ) If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter in the "Control Panel System Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Note If problems repeatedly occur, contact an authorized service center. Q&A Q: A: A: Q: A: How can I change the frequency? [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SAMSUNG SYNCMASTER T27B750ND




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SAMSUNG SYNCMASTER T27B750ND will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.