User manual SENTROL ZXVFD

[. . . ] How to Use Your Sentrol Security System ZXLCD/ZXVFD Control Station VIEW INFO ALM MEM EVENT LOG OFF CANCEL D 1 BYPASS 2 DELAY ARM 3 CHIME 4 AWAY RST SMOKE 5 TEST 6 PROGRAM 7 QUIT 8 ACCESS 9 INSTANT STAY CLEAR HOME 0 ENTER NEXT NIGHT 1 INTRODUCTION Thank you for choosing the ZX200/ZX210 or the ZX400/ZX410/ZX440F Security Control. This control will provide you with years of reliable operation when properly installed and maintained. To maximize the benefits of your Security System, it is important to carefully read the entire contents of this manual and become familiar with all control operations. Your Security Company Representative has recorded confidential information about your system in this manual, therefore, you should store it in a secure place. [. . . ] Do not perform this operation during walk test mode or when any keypad is in use. This feature allows you to program a name in for each zone location (i. e. : zone 1 is the Front Door). Press CLEAR + ENTER at the same time. The Control Station will display: ZONE 00 SELECT ZONE ID 2. Press ENTER . See Protection Zones for a list of zone numbers. 3. The Control Station will display the zone number selected on the first line and the zone name to be programmed on the second line. Press the key associated with each character listed on the next page to enter in the new zone name. Each keypress will change the display to the next character listed for that key. A maximum of 12 letters (includes spaces) may be used for each zone name. 32 ZX200/ZX210 PROGRAMMING Key Character Available 0 A D G J 1 B E H K 2 C F I L O R V Y !/ S 3 4 5 6 7 8 9:; <=> ?@ 1 2 3 4 5 6 7 MN P T Q U 8 9 WX space 0 %& Used to move the cursor back one position Used to move the cursor forward one position 4. Press CLEAR to start over if a mistake is made or press ENTER to save the zone name and return to the zone number prompt. Press CLEAR from the zone number prompt to exit. 33 ZX400/ZX410/ZX440F PROGRAMMING ZX400/ZX410/ZX440F Programming Your system has several features which you may be able to program yourself. DO NOT attempt to program the system unless you have been properly trained on programming procedures and you fully understand these operations. There are eight (8) options available: 1 Remote Connect Allows the installer to program and diagnose problems from a remote site using the telephone lines. (Military format) Schedules your system to automatically turn ON at a specific day(s) and time(s). Allows you to change any passcodes. 2 3 4 5 6 Set Clock Program Automatic-ON Program Latch Key Program User Codes Cancelling Automatic-ON Cancels the system from automatically turning ON for the scheduled time for that For Today day only. Cancelling Exit-ON For Today Program Zone Names Cancels the system from automatically turning ON for Today 10 minutes after you leave the premises for that day only. Allows you to enter a name to each zone. 7 8 Remote Connect Contact your Security Company Representative for instructions. 34 ZX400/ZX410/ZX440F PROGRAMMING Set Clock The clock is set according to military time (24:00 hours). Press 9 . The Control Station will display: TO PROGRAM ENTER PASSCODE 2. Enter passcode: The Control Station will display: SELECT PROGRAM OPTION 1-8 3. Press 2 . The Control Station will display: 10:53 02/04/97 ENTER = COMPLETE 4. (See example) Example: To set the clock to 2:15 pm on June 17, 1997: Press 1 0 CLEAR 4 6 1 1 5 7 (2:15 pm) Press 9 7 (June 17, 1997) 5. Press to start over if a mistake is made or press ENTER to save changes. 35 ZX400/ZX410/ZX440F PROGRAMMING Programming the Automatic-ON Feature (DO NOT enable for UL Listed Systems) This feature allows you to automatically turn your system ON at certain times for certain days. Setting the Security Level Day(s) of week to automatically turn ON Hour to turn ON each day Minute to turn ON each day A. Enter passcode: The Control Station will display: SELECT PROGRAM OPTION 1-8 3. The Control Station will display the current setting. 6. Press 0 for AWAY, press 1 for STAY, or press 2 for NIGHT. [. . . ] An AC surge arrestor should be installed in the system's AC power outlet. Part 15 Notification This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]