User manual SHARP AL-1631

[. . . ] MODEL AL-1631 AL-1641CS DIGITAL LASER COPIER DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL Page INTRODUCTION SETTING UP THE UNIT LOADING PAPER INSTALLING THE SOFTWARE (AL-1641CS) MAKING COPIES SPECIAL FUNCTIONS MAINTENANCE TROUBLESHOOTING THE UNIT APPENDIX 4 7 14 19 46 52 57 61 68 AL-1631/AL-1641CS FOR YOUR PROTECTION. . . To aid in reporting this unit in case of loss or theft, please record below the model number and serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference. MODEL NUMBER DATE OF PURCHASE Dealer Address State Service Station Address State Zip City Telephone Zip City Telephone SERIAL NUMBER To obtain service, or to obtain product literature, accessories, or supplies, please call or 1-(630)378-3590 in the USA 905-568-7140 in Canada. For customer assistance, please visit http://www. sharpusa. com/ (for USA) or http://www. sharp. ca/ (for Canada) on the World Wide Web or call 1-(630)378-3590 (for USA). Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. [. . . ] Then make desired copier selections and press the start ( ) key using the normal copying procedure. Auto clear (page 55) The unit returns to the initial settings a preset amount of time after the end of copy, or scanner job. This preset amount of time (auto clear time) can be changed. Stream feeding mode (page 55) For description of the stream feeding mode, see "Stream feeding mode" (p. 48). Resolution of AUTO & MANUAL mode (page 55) You can set the copy resolution used for AUTO and MANUAL ( mode. ) exposure TONER SAVE MODE 1 Press the exposure mode selector key to select the MANUAL ( ) mode. 54 2 Press and hold down the exposure mode selector key for approximately 5 seconds. The MANUAL ( ) indicator will go out and the PHOTO ( ) indicator will begin to blink. The light and dark indicator marked "5" will light up, indicating the standard toner mode is active. The light and dark indicator marked "1" will light up, indicating the toner save mode is selected. 3 4 Press the exposure mode selector key. The toner save mode is now active. To return to the standard mode, repeat the procedure but use the dark ( ) key to select exposure level "5" in step 3. USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. Setting the power save modes, auto clear time, stream feeding mode and resolution of AUTO & MANUAL mode 6 1 2 Press and hold down the light ( ) and dark ( ) keys simultaneously for more than 5 seconds until all the alarm indicators ( , , ) blink and " " appears in the display. Use the left copy quantity ( ) key to select a user program number (1: auto clear time, 2: preheat mode, 3: auto power shut-off timer, 4: stream feeding mode, 5: auto power shut-off mode 6: resolution of AUTO & MANUAL mode). The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the display. The entered parameter number will blink on the right of the display. 3 4 55 Program No. 1 2 3 4 5 6 Mode Auto clear time Preheat mode Auto power shut- off timer Stream feeding mode Auto power shut- off mode Resolution of AUTO & MANUAL mode 0 *3 *0 0 3 0 0 *0 Parameters OFF, 1 10sec. , 2 30sec. , 60sec. , 4 90sec. , 5 120sec. 30sec. , 1 2min. , *1 30min. , 4 OFF, *1 OFF, *1 300dpi, 1 60sec. , 2 90sec. 5min. , 2 15min. , 60 min. , 5 120min. ON ON 600dpi * Factory default settings are indicated with an asterisk (*). 5 Press the start ( ) key. The right-hand number in the display will be steadily lit and the entered value will be stored. To change the setting or to set another mode, press the clear ( ) key. The unit will return to step 2. 6 Press the light ( copy mode. ) or dark ( ) key to return to the normal DISPLAYING TOTAL NUMBER OF COPIES Use the following procedure to display the total number of copies. Press and hold down the clear ( ) key for approximately 5 seconds. The total number of copies will appear in two steps, each with three digits. Example: Total number of copies is 1, 234. 56 7 MAINTENANCE This chapter describes how to replace the TD cartridge and drum cartridge and how to clean the unit. Be sure to use only genuine SHARP parts and supplies. TD CARTRIDGE REPLACEMENT The TD cartridge replacement required ( ) indicator will light up when toner is needed. For more information on purchasing the TD cartridge, see "ABOUT SUPPLIES AND OPTIONS" (p. 70). If copying is continued while the indicator is lit, copies will gradually become lighter until the unit stops and the indicator begins blinking. · After the unit stops, it may be possible to make a few more copies by taking the TD cartridge out of the unit, shaking it horizontally, then reinstalling it. If copying is not possible after this operation, replace the TD cartridge. [. . . ] 5 Software for the SHARP Personal MFP series. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 TD cartridge replacement required indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 51 INDEX BY PURPOSE Checking the package . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cleaning the unit - Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]