User manual SMEG ALFA150

[. . . ] INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test. 23 General instructions 1. INSTRUCTIONS FOR USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE APPLIANCE. CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE APPLIANCE IS ESSENTIAL. [. . . ] Do not discard the packaging or any part of it, or leave it unattended. It can constitute a suffocation hazard for children, especially the plastic bags. Important: hand over your appliance to the local agency authorised for the collection of electrical appliances no longer in use. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power supply network, removing it along with the plug. 28 Instructions for the user 4. GET TO KNOW YOUR OVEN Oven interior in glazed fire-stone Steam discharge Oven light Rack/tray support frames (Standard frames are shown for illustrative purposes) Control panel Gasket 29 Instructions for the user 4. 1 DESCRIPTION OF THE CONTROLS START BUTTON: This button allows you to start cooking. STOP BUTTON: This button allows you to stop cooking at any time. DISPLAY: Displays the selected program and relative cooking parameters. PROGRAM SELECTION KNOB: It allows you to set the cooking operation using one of the programs, to select the cooking temperature and time. STEAM DISCHARGE KNOB: During cooking, this knob allows you to eliminate the steam produced after cooking food. The discharge settings range from 0 to 1 and all the intermediate zones can be used. 30 Instructions for the user 5. USING THE OVEN The oven is designed for a maximum load of 3. 5 kg. 5. 1 General warnings and advice When using the oven for the first time, heat it up to its maximum temperature for a time long enough to burn off any oily residues from the manufacturing process. 5. 2 Choice of programs This appliance allows you to select 40 cooking programs including: · 39 programs that can be edited and saved as the user wishes; · 1 preheating program with delayed start "P40"; Below we provide a table of the heating elements power splitting for each program: Prog Upper Lower Prog Upper Lower 1 100% 10% 22 80% 100% 2 100% 10% 23 80% 100% 3 100% 10% 24 80% 100% 4 100% 30% 25 60% 10% 5 100% 30% 26 60% 10% 6 100% 30% 27 60% 10% 7 100% 60% 28 60% 30% 8 100% 60% 29 60% 30% 9 100% 60% 30 60% 30% 10 100% 100% 31 60% 60% 11 100% 100% 32 60% 60% 12 100% 100% 33 60% 60% 13 80% 10% 34 60% 100% 14 80% 10% 35 60% 100% 15 80% 10% 36 60% 100% 16 80% 30% 37 0% 100% 17 80% 30% 38 0% 100% 18 80% 30% 39 100% 0% 19 80% 60% 40 100% 10% 20 80% 60% 21 80% 60% Power splitting percentages cannot be edited by the user. 31 Instructions for the user 5. 3 Editing / saving a program The oven has 39 programs that can be modified by the user (from P01 to P39). To set the operating parameters of a program: 1 2 3 4 5 6 Turn the knob to the or symbol to select the program you wish to save/edit. Keep the "PUSH" knob pressed for 3 seconds: the display will show the cooking temperature. Press the "PUSH" knob: the display will show the cooking time. Turn the knob to the or symbol to set the cooking duration time (from 1 to 99 min or INF infinite). Press the "PUSH" knob to exit from the data setting and saving phase. The message "PEnd" will appear on the display and the parameters will be saved. To return to the "OFF" status keep the "STOP" button pressed for 4 seconds. 7 8 5. 4 Running a program From the "OFF" status proceed as follows: 1 Turn the knob to the or symbol to select one of the available programs from P01 to P39. The display will show the parameters of the selected program in rotation. The appliance will perform a preheating cycle, showing the text "PrEh" on the display. When preheating is finished, a series of buzzers lasting 3 seconds will indicate that it is possible to proceed with the cooking operation. To start cooking, keep the "START" button pressed for 2 seconds. The display will show the set parameters in sequence, the time remaining until the end of cooking and the program selected. [. . . ] ATTENTION: if the phase voltage drops below 190V , the performance of the oven may suffer, not due to the product itself. The terminal indicated by this symbol links up parts that are normally earthed. Connect the appliances properly using this terminal in order to make sure that they are equipotential. 8. 1. 1 Safety thermostat The oven is equipped with a safety device that triggers in case of serious malfunction. [. . . ]