User manual SMEG CWC610

[. . . ] PROFESSIONAL DISHWASHER CONTENTS CWC 610 1 PRECAUTIONS FOR SAFETY AND USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 INSTALLATION AND POSITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 INSTRUCTIONS FOR TECHNICAL STAFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4. 1 Plumbing hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4. 2 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5. 1 Display Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5. 2 Note on display of temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5. 3 Parameter programming procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] These switches must be installed close to the dishwasher, be easily accessible after installation, and provide complete disconnection from the electrical mains in 9 overvoltage class III conditions. The dishwasher is always powered up unless the master switch is turned off. The terminal for the connection is in the bottom righthand corner of the appliance. The earth wire (PE) is yellowgreen in colour, the neutral wire (N) is blue and the live wires (L1, L2, L3) are black, grey and brown. THE POWER SUPPLY CABLE MUST BE REPLACED BY THE MANUFACTURER OR AN AUTHORISED SERVICE CENTRE TO PREVENT ALL RISKS. The dispenser must operate on 230V/50 Hz with maximum power absorption of 15 W. Connect to the detergent dispenser outside the dishwasher using the red hose mentioned above. IMPORTANT: Whenever the type of detergent or rinse aid is changed, it is ABSOLUTELY ESSENTIAL to flush out the peristaltic pumps by placing the external intake pipes in water for a few cycles. Always use only products specifically recommended for use in a dishwasher. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance's water system. The internal pipes of the detergent and rinse aid pumps should be replaced by the AfterSales Service every 12 months or 15, 000 wash cycles and operation of the diaphragm rinse aid pump should be checked. 12 CWC 610 5 SET-UP Setup During first startup, the functions/parameters listed below must be set or adjusted: A series of operations can be carried out when the dishwasher is first installed to customise it to the user's requirements. 5. 1 Display Contents The two green digits provide the following information: Appliance off but powered up: all decimal points on both digits Appliance on: Boiler temperature Washing phase: Tank temperature Pause phase: Boiler temperature Rinse phase: Boiler temperature Programming phase: See parameter programming section Error message: See error messages section 5. 2 Note on display of temperatures Both the Boiler and the Tank temperatures provide instantaneous readings of the current value picked up by the probe, but due to the thermal inertia of the probe or its seat, wait about 1' after the heating element power absorption reading to obtain the real temperature. 5. 3 Parameter programming procedure To access the programming menu, proceed as follows: 1) switch the appliance off with the (On Off) key 2) Within 6 seconds, press key P1 (SHORT wash) 7 times. Wait for the 6 seconds to pass; at the end P0 appears on the display 3) Use key P1 to select the parameter to be modified 4) Press the PUMPOUT KEY to display the parameter for modification 5) Modify the parameter by pressing key P1 6) Confirm the change by pressing the PUMPOUT key 7) Select the other parameters for modification in the same way and proceed as described above 8) After setting all the appliance parameters, press the On Off key to quit. 13 5. 4 Modifiable parameters CWC 610 This table lists the model choice or cycle and temperature option parameters. F/M M F M M M M M M M F Note for P6 and P7: negative numbers are indicated by illumination of both decimal points (e. g. : 12 "1. 2. ") ID P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 Description Appliance Type Appliance Model Boiler temperature Tank temperature Thermostop option Soft Start option Boiler temperature offset Tank temperature offset Real temperature display Tank probe type 610 4 4 80C 58C 0 1 0 4 1 1 Notes Construction version Do not modify Do not modify Step 1 degree do not set above 85° Step 1 degree 0=off 1=on 0=off 1=on Real=measured+Offset Real=measured+Offset 0= filtered, 1= real Do not modify 5. 5 Alarm trigger time thresholds This table lists all the safety device trigger time thresholds. F/M F F F F F ID A0 A1 A2 A3 A4 Description Boiler max. heating time Maximum water intake time Maximum emptying wait time Default 20 min 50 min 5 min 1 min Notes Step = 1 min Not active with PL ON Step = 1 min Step = 1 min 14 CWC 610 5. 6 Adjusting detergent and rinse aid dispensing Caution: ensure that the appliance is not powered up ELECTRIC SHOCK HAZARD RD RB RV Detergent dispensing regulator screw (on some models only) Rinse aid dispensing regulator screw Inspection panel removal screw RD: Detergent dispensing regulator screw. (on some models only ) Adjustments are made using the adjuster screw AS SHOWN. The quantity dispensed is reduced by turning anticlockwise and increased by turning clockwise. RB: Rinse aid dispensing regulator screw Adjustments are made using the adjuster screw AS SHOWN. [. . . ] Plates/glasses badly arranged Low washing temperature Inappropriate cycle set Dynamic pressure of mains water insufficient Spray arm nozzles fouled Limescale in boiler Rinse aid unsuitable or not being delivered correctly. Water hardness above 12°dF or large amounts of dissolved salts Drain hose incorrectly positioned or partially obstructed. Remove spray arms and clean them (8. 2 Periodic checks) See "Cleaning the filter during the day" Check type and quantity of detergent. Check temperature shown on the display, call the aftersales service if less than 50°C Increase wash cycle duration, especially if dirt has dried on. [. . . ]